I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
I am using a nrf52 dev kit as well as a raspberry pi to set up the cloud coap example in the nordic docs. I have set up a 6-4 tunnel through hurricane electric and have full...
Hello,
I'm playing beep sound using pwm1 (timer1).
The onSound() starts beep sound.
The disableBuzzer() terminates pwm1.
The handler_buzzer() selects continuous...
Hi,
I'm using nrf51822 and ble_app_uart in SDK12.3.
Testing with android app nRF UART v2.0
I have some problem with BLE connection.
First, Sometimes when I tried...
Dear Nordic:
I have transplanted my code from sdk 10.0(nrf51422+S310) to sdk 13.1(nrf52832 + s332(v4.0.2)).
I program softdevice and application to my board by nRFgo_Studio...
I just tried to add a custom service, so I expanded my ble_cfg.gatts_cfg.attr_tab_size.attr_tab_size. Now, when I call sd_ble_cfg_set(BLE_GATTS_CFG_ATTR_TAB_SIZE, &ble_cfg...
Hi everyone,
For my project I'm currently using the sdk 10.0.0 (S310 on a nRF51422) and I would like to use the Secure DFU provide by the sdk 12.0.x.
Working on a nRF51422...
Hi everyone
We have a custom made board with NRF52832 chip. We are send it to FCC test lab and they told us the occupied bandwidth (OBW) is too small, 940kHz less than...
Hello,
has anyone tried new v1.1.0 for nRF6707? If I change the window size to more than original 2.0s, GUI becomes very laggy and it is very hard to stop the recording ...
Hello,
I've been trying to test DFU over UART which has been added in SDK13.1 but after following every resource I've found I always end up with DFU not working
The...
I found this question which partially answered what I am looking for:
devzone.nordicsemi.com/.../
Essentially, if I am creating a new project with my main.c file and...
Hi I am trying to design a custom BLE board using NRF52832 by following the reference layout.
I am new to RF design and I have got a few questions that I would really appreciate...
Hi
I'm trying to implement DFU in my project. So far, after I sending 01-04 to the control point characteristic(1531)，I can get bootloader signal, to be exactly, i can enter...
Hi,
Can we interface a smbus based sensor with NRF51 or NRF52? The only difference between smbus and TWI is the minimum speed requirement which is 10Khz if I am correct...
Dearl all,
I want use the eclipse and gcc together to program the board nRF52840 Preview DK. I was following the tutorial devzone.nordicsemi.com/.../.
I followed the...
Hi,
I'm using nRF52832 with sdk 13.0.0(softdevice 4.0.2).
I had trouble to connect nRF52 and some android 7.0(or upper version) smart device.
I tested samsung galaxy tap...
