Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
Hi,
I am trying to figure out a way to update the toolchain and SDK for an nRF Connect for VS Code installed on an offline machine, without much success.
From https:/...
Hello,
I am working with the NRF9151 DK on DECT NR+ and I want to change the subcarrier scaling factor and subslot value in the hello_dect example. However, I am not sure...
NRF Connect SDK (v2.8.0), VS Code, NRF52840
Hi, while reading the Zigbee documentation I saw the following note:
"Support for Zigbee R22 has been deprecated in nRF Connect...
I am simply trying to build the hello world (and blinky, results are the same) with NRF-SDK 1.8.0 - it's based on Zephyr 2.7, which is the LTS release.
Target board is 5340...
Hi,
We are planning a new project that needs to use very low power. Since relay mode uses more power than simple node, can we turn off relay mode on all nodes until an event...
Hi, I am developing BLE beacon application on the nrf52820 soc which has limited Flash resources. I want to have the FOTA through BLE abilities built in to enable firmware...
Hi! Can you please help me identify what is causing this issue and/or provide more info about this:
[00:04:23.038,330] \033[1;31m<err> bt_sdc_hci_driver: SoftDevice Controller...
Hello everyone!
I'm working with the nRF52840 microcontroller and I wanted to get a bluetooth antenna and since I know that the whole RF thing is very complicated, I was...
Hi.
I have a custom board with a NRF9161. The nrf91's LTE block connects to the sim holder through a NX3DV2567HR switch and an TPD3F303DQDR ESD protection.
I'm using...
Hello there, Describe the bug When setting a breakpoint inside an IRQ handler in my application, I'm experiencing the following crash each time I try to continue, step over...
I am working on integrating an external antenna with the EYSHSNZWZ BLE module from Taiyo Yuden, which uses Nordic’s nRF52832 SoC . The biggest problem is that I cannot confirm...
Hello. I have designed in the nRF52840 into a product and we've seen this issue on at least two prototypes. The RESET pin seems to get stuck low (grounded) and I can't seem...
Hello I am working with the nrf54l15 soc (sdk 2.8.0).
I have noticed that a component "mx25r6435f" is defined in the generic nrf54l15_cpuapp_common.dtsi file.
With some...
