Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
hello:
My project is based on "esb_rx",NCS2.5.1，nRF52832.I need a Unique address for my product ,so I add flash read/write function for my projict, base on "soc_flash_nrf...
Hi,
we are facing an issue of loading the application written with nRF Connect SDK to the nRF52840 which has nRF5 SDK's secure bootloader. Update process should be performed...
I try to enable APPROTECT by nrfjprog but seems not work, I still can read the memory after device (PCA10090) reset.
Here is the commands I test to enable APPROTECT
...
I was trying to update the PPK II software, but I am receiving a error message: "Error: EPERM: operation not permitted, mkdir 'D:\'"
Well, in my Windows environment, the...
Hi,
We have been using the DeviKit for our initial development and now we have developed our own custom board using the nRF5340. I trying to flash the device, but couldn...
Hi, We noticed that if you do not "Disconnect" a SEGGER RTT connection (on the RTT Viewer), the nRF52832 chip latches into using a relatively large amount of power (~3mA)...
I'm running the latest nRF Connect under VS Code on Windows 11.
What used to compile and not show errors (a couple weeks ago, and running 2.6.0) is now showing errors on...
I am having a problem where the UART is getting noise and bad data (I assume framing errors too) with Zephyr drivers. I was wondering how in Zephyr do you check for framing...
Hello,
This demo gives me automatic pairing and password input.
https://devzone.nordicsemi.com/f/nordic-q-a/44658/communication-problems-between-ble_peripheral-and-ble_central...
This question is in lieu of an issue on the repository, because I don't think issues are accepted there?
I noticed I was getting the following CMake Warning:
Could not...
I am running on demo "nrf-knx-iot/samples/light_switch_sensor".
I built the demo and burned it into my nrf52840dk successfully, but I could not see more logs.
I found...
Hello! We recently acquired a Nordic Thingy:91 for prototyping and it was working great until I came into work this morning and it was no longer showing any signs of life...
Hi Support team,
When I compile the application on the network core of nRF5340, the result is like below:
There is a 64KB SRAM1 with usage 0%, could you tell me what is...
Issue: No Interrupt Signal on GPIO0 Pin of MAX30208 Sensor with Xiao BLE nRF52840 Using Zephyr NCS v2.6.1
I was write a code for max302078 sensor driver but in this i want...
In some examples that use nrfx libraries it is necessary to extract a GPIO PSEL, which is usually done like this. Give the following DT definitions
``` leds {
compatible...
