Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello sir/Ma'am
I am working on a project in which i am using some BLE peripheral devices, an Central device and an Android app. I want to get data on android app from central...
I'm trying to program nrf9160 but getting an error due to readback protection.
I have tried the following commands:
nrfjprog --recover
nrfjprog --recover -f NRF91
...
I set an NOPULL type input GPIO, and I found that if I put in a voltage of about 1V,
the nrf52832 will produce a current of about 30uA,
I want to know why it can be happen...
HI
I have using nrf5340 DK for the past 7 months. Sometimes, The DK gets powered up only after 2-3 minutes after giving the power supply from the PC. Even after powerup...
I'm working on a project based on nRF52840 and nRF5 SDK16. I'm using BLE with softdevice S140 7.0.1 and USB CDC ACM for communication with a USB host. Ultimately the problem...
Hi,
I'm trying to run ble_app_blinky_pca10040_s132 on Fanstel BT832 custom board with no success. After writing/verifying the app using the SES it jumps to 'unknow function...
Hello,
I have a question:
i want to send a JSON payload using the PUT-method from CoAP. For this I am creating my JSON Payload with the following function:
The main...
I am in the conceptual stages of development for a BLE test system.
The test system requires:
Fast transceiver and connection with BLE devices, preferably capable...
I know Nordic is releasing the nrf9160 on the 12/12/2018, and from what little documentation I can find it doesn't seem to have BT or NFC hardware integrated. Are there any...
Hello, I have installed nRF Connect and the Programmer following https://infocenter.nordicsemi.com/pdf/nRF9160_DK_Getting_Started_Guide.pdf At step 3.2.2 i see "No devices...
Where can I find a drawing of the footprint for the nRF52840 WLSCP? Normally it would be near the end of the datasheet, after the mechanical drawing of the package. The datasheet...
I have an application running a serial communication through a RS485 interface. I have two sensors attached through I2C/TWi.
I have a app_timer that quwry the sensors once...
I have built on the CoAP example a POST request to the server. This works now without any problems.
I do send the received signal power within my POST. To get the power...
Hi,
I purchased a NRF9160 DK and am having problems on the first time I am trying to compile the SERIAL_LTE_MODEM application . I followed the steps according to the documentation...
