Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
i have a function wich just send "hello world" via uart0. static otError SendUARTCommand(void) { volatile uint32_t ret; const uint8_t message[] = "Hello World! \n...
Hi !
This is more of a question than an issue. I am curious about the future of TF-M and its implementation on Zephyr. Does anyone know what are the plans on Zephy's or...
I'm trying to set tx power to +3db in the peripheral_uart sample.
I don't need dynamic control, just setting to always use +3db.
Adding the following line to prj.conf...
Hi,
I am using coded BLE to connect two board using nrf52840. I just let bluetooth to run, then measure power consumption of the peripheral board by measuring the current...
Hi,
I am trying to send messages from my gateway, which has UART and __LOG enabled, to a specific LPN address (0003).
So I want to send messages from my FN Light1 (0002...
We have developed an application in ncs-1.3.0 where we created a west.yml file for the application that lists nrf, zephyr and other dependent repositories. We have downstream...
Hello. everybody.
I'm new to be here.
Now, I'm struggling to succeed in building 'ble_app_beacon_pca10040_s132.uvprojx'.
(This file located in C:\(private dir)\nRF5_SDK_12...
We encounter 52810 freezing problem. It occurses in low probability less than 1 out of 1000.
Power-on reset is no use for this problem. The freezed 52810 chip restored when...
Hello,
I am developing a product that acts as a peripheral and sends a notification of more than 20 bytes (which is by default the BLE MTU). How can I config the MTU so...
Hallo I'm writing Data to the I2C port.
I'm using the nrf_drv_twi_tx function. It works well.
But I want to write bytes to the I2C without Adress. - i want to write just...
Hi,
I have the nrf5340 development kit. This is my first time working on Nordic devices. I've followed the Getting Started Guides. I am trying to run the first test. My...
Hi,
I'm trying to m ake sure that the nRF Sniffer files can be run correctly, following the instructions: "On Windows, type nrf_sniffer_ble.bat --extcap-interfaces".
The...
Hi,
Can you please explain what is the usage of unconnectable advertising? And what is the difference between beacons and unconnectable advertising?
Thanks!
What does (15U) mean ? Is that a specific useage declaring a number?
What does " =='\n' " means ?
After a long period of learning , I'm now trying to read and understand...
Hi everyone,
I am making a zigbee mesh with just coordinator and routers only. I intended to have the mesh to cover a very large areas with nodes that can be moved (not...
