Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Again no where I can find to put this. Also under documentation as a tag you need another option to select, e.g. SDK
Anyhow, When I try and search the documentation the...
I think I've found a bug in the power management that occurs only when a softdevice and the debug interface are active. In SDK v17.0.2, nrf_pwr_mgmt.c lines 417-429:
The...
Hi,
We using nRF Connect SDK,
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/libraries/zigbee/lib_zigbee_shell.html#zigbee-shell-command-list
We founded...
Hello,
I am working on nrf52833 using the soft device s140 ble with csence enabled.
but the cap button has problems to detect signal, what is the
THRESHOLD_BUTTON...
Hi,
I'm using nRF5 SDK, use original build. No change anything. Just enable the Zigbee CLI as Coordinator.
After tested with various devices, found out a lot devices...
Hello. I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0).
I use whitelist to store bonding information. Is there an upper limit to the number that can be stored...
Hi,
I am trying to configure a GPIO pin P0.21(as this is exposed pin on Thingy:91) from nRF9160 on Thingy:91.
I am using nRF Connect SDK 1.4.1 with Nordic version of SES...
Hi,
I am evaluating the LTE modem demo. I downloaded the demo binary firmware images a few weeks ago. Today I installed the LTE Modem demo into my dev kit. It connected...
I want to develop a 2.4G mouse Dongle and have used NRF52840 and SDK 17.0.2. When I have used USB or ESB one by one - all is Ok. But when they are used together - usb driver...
Hey all
I've been searching and trying all sorts of options for this but I'm stuck.
I'm currently working on a Thread sensor prototype on the 52840DK. I'm trying to...
There are two issues in one here. The easy fix is the check for overflow in format_offset_string_print() if (length <= p_cli->p_ctx->vt100_ctx.cons.terminal_wid - terminal_offset...
I have a bit of an odd one, and would appreciate any input. We have a fairly complex project, which does various things, but some of the time, I get a hardfault. The issue...
I am getting linker errors such as the following:
Output/Release/Obj/saadc_pca10056/nrf_sdh.o:SDK\components\softdevice\common/nrf_sdh.c:83: undefined reference to `start_sdh_req_observers...
Hello i have a keyboard with nrf52840 with ZMK firmware, BLE, adc, gpios, i2c0, usbd, DCDC and CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC
When it is connected with the computer...
