Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hello,
In my project, nrf_drv_gpiote_in_init is used 3 times.
battery measure
sleep trigger by motion sensor
wake-up trigger by motion sensor
After 3rd call...
HI
I am trying to interface ads1231 with nrf5340. Regards I need to know about Gpio read. Because ADS1231 gives digital output. I don't know how to read actually. Kindly...
What is the purpose of the ble_advdata_encode() method?
I see it has been used in the beacon example, but some other examples don't use it.
In both case, the advertising...
Hi, all..
An error occurs as soon as it connect and disconnect through advertising. Timer interrupt is currently running on the main function..
and then I found error...
OS: Mac
I installed nrf v1.2.0 and Segger Embedded Studio v4.42a. I can't open project and it causes error.
I can open projects with this config on SES v4.42a and...
Hello,
I installed Segger Embedded Studio v 5.34a following the online instructions AND the Getting Started Assistant instructions for a Mac. I then tried to import a project...
Hello everybody,
I'm trying to develop mesh network with zephyr, but the problem is that logs are not displayed in SES debug terminal. In autoconf.h file I can see that...
Hi,
I have been following this post and did all the steps instructed by , but I failed to receive a response in Tera Term in the end. I have also tried changing the hostname...
Hi,
Need help to interface nrf9160 with MSP430.
Making Project where MSP430 will collect the data from ECG sensor and sending to nrf9160 in packet form. nrf9160 will going...
Hi,
Time to time, Our board stuck in QDEC_IRQHandler.
1) In which case QDEC_IRQHandler could occurs?
2) I want system reset from QDEC_IRQHandler automatically.
But...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0).
During development, I was wondering about advertised packets.
I thought that the advertisement packet...
Hello ,
I have configured one nrf52832 where it sends temperature data over one service's characteristics ( updating the value after every 1 min ) and I am able to see this...
Hello. I am trying to scan for BLE packets and write them out through USBD using nRF5 SDK v15.3.0. I am calling app_usbd_cdc_acm_write() in scan_evt_handler when an event...
If I update prj.conf in a zephyr project, but I'm building with segger and the connect sdk (1.5.1) do I have to do something besides "Build / Rebuild" to get segger to recognize...
