pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
Hello. I have a misunderstanding about the work of the mesh network. Let's say I create a group of proxy nodes, example light switch, 2 server and 1 client, . I connect with...
Hello,
Here is my work env.
NCS: v1.5.0
board: nrf5340dk
I found this way to open DCDC，but the nRF5340_PS_v1.0.pdf said these register are Retained.Can you give me...
Hello,
Merry Christmas!! Nordic Semi
We are developing NRF52840 application using SPI bus, however the slave we are communicating with requires data rate larger than...
Hi,
I've a secure UART DFU that's running great with the nRFUtil. I'd like to integrate the same functionality with a custom Windows Application for our product.
I...
Hi,
Can u suggest the procedure to implement key refresh procedure with reference to the API present in nrf SDK as per the standard procedure defined in Mesh Profile Spec...
Hi community,
I have recently purchased the DK and have started developing my application. What I wish for it to to is able to change between connectable and non-connectable...
I've just got started with nRF Connect and used the desktop app to install SES and the SDK v1.5.0.
I am trying to evaluate NRF52805 using an nRF52-DK board, so I selected...
Hi
Good Day!!
Im using keil ide While compile the code for crypto aes getting error could no be solved, plz give the solutions for this issue
.\_build\nrf52840_xxaa...
To the kind attention of Nordic support team,
I m developping for a nRF52833 device using two different versions of custom boards. According to antenna measurements and...
Hi,
when I build a firmware with TF-M enabled the device gets stuck after a ca ll to sys_reboot(...) no matter if I use the shell or call the function somewhere else in...
Hi,
I am using SDK_15.2.0 and softdevice S140_v6_1_1.
Host communicate with 52840 via USB (CDC UART). Doing firmware update with proprietary message format.
Stored...
When checking the secure_dfu code, I found the following two code fragments seemed problematic in nrf_bootloader_fw_activation.c
1. In the following one, if the ACTIVATION_ERROR...
Hi, unfortunately, I do not have enough experience with nRF52. Could you please tell me what should I do for scanning the nRF board on the BLE scanner app? The app can find...
I am using a thingy:91 device. I am basically just attempting to write a method that will just wait for a certain amount of seconds (ie: 10 or longer). This is my code below...
