In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Hi,
I am using my nrf52832 board with a MPC9808 sensor and I wanted to use the example code provided in zephyr/samples/sensor/mcp9808
Can you tell me with which pin of...
i'm building an amplifier that can play sound over bluetooth. I intend to use the nrf52832 to send i2s data to my dsp chip. based on the loopback example, i have an idea on...
Hello,
I was reading through the code of the asset tracker application and noticed that there is no while(1)/for(;;)-loop. I see this for the first time in a board application...
hello,
we are in process migrating to SDK 16.0 and service pack 8.27 or higher. While performing an upgrade we encourage few problems and would like you expert advise...
2 Questions, both short:
1. Documentation error in Softdevice 15.x and 14.x header files:
/** @note If any of the discovered services have 128-bit UUIDs which are not...
"AT+CEREG=2" "AT+CFUN=1"
Getting the correct responses of above mentioned AT commands.
But after that, when any command is send on LTE Socket, " at_host_at_socket_write...
Hi,
I was randomly inspecting Bluetooth devices around in nRF Connect and I found out that many Apple devices advertise with TX Power Level 12 or 24 dBm. From my understanding...
Dear Nordic Team,
I'd like to inquiry how I am supposed to send a UTF8 string as the value of a characteristic.
I am trying to implement the FTMS service and the part...
Hi !
I want to connect 2 of my units to each other via BLE5 long range coded phy (125Kb).
I also want to be able to connect an android / ios phones to each unit simultaneity...
Base Samples used -
1. Central DFU SMP Client - <ncs>/nrf/samples/bluetooth/central_dfu_smp
2. SMP Server sample - <ncs>/zephyr/samples/subsys/mgmt/mcumgr/smp_svr
...
I am using the "ble_app_multilink_central" in version nRF5_SDK_17.0.2_d674dde for development.
It works and can connect to BLE devices.
However, there is one issue
...
I'm trying to use the BLE CLI example (ble_app_interactive) available on nRF5_SDK_17.0.2 on my nRF52840 chipset (on a BL654 kit) and as soon as the interface starts I receive...
Greetings,
I've got the power profiler app (v3.0.3, installed via the nRF connect desktop app v3.6.1) running under both Linux and Windows.
With windows, seems to work...
Hi, everyone,
I am pretty new to nRF52 development. Right now,I want to turn SAADC off at low power and turn it back on when wake up, but after nrfx_saadc_uninit(); When...
