Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello.
I m working with mesh demo: https://github.com/NordicPlayground/thingy52-mesh-provisioning-demo
In Android app we can press "identify" and after that Thingy's led...
Hi, On a button press I need to enter to disconnect from the currently connected device and then start advertising in order to allow a new device to connect. I manage to disconnect...
I am trying to read analog value from a GPIO pin. Particularly I want to read battery voltage from a GPIO pin assign to P0.31. Please help me how can I read the analog va...
Dear All,
Thanks for your continued support.
I have been trying to get debug terminal to work... I enabled RTT log and disabled UArt in the sdk_config file. I set...
Hello!
I'm trying to handle an interrupt using a timer.
Is it okay to write something like the following?
Also, if this is called every 1ms as interrupt processing...
Hello,
Im using D52Q ANT Module series chip, I have uploaded the S132 soft device and BLE peripheral program(PCA10040).
Once i download the program, 3rd LED glows, and...
Hi everyone,
I'm working on a project where I need to send sensor data from multiple sources to a PC. So, I'm using multiple SparkFun Pro nRF52840 Mini board (Peripherals...
Hi,
I'm using SDK v3.2 and I'm extending the lighting example. I'm developing an extension to the provisioner, to inform a back-end about the configuration of the subnet...
Hi,
our device has current limitations in the range of 1mA. We were examining several ways to limit the actual connection parameters to keep current consumption low. But...
Hi,
I'm developing an application to monitor the current application and network context, by extending upon the existing Light Switch example in nRF5 for Mesh SDK v3.2.0...
Hi everyone !
I have 3 services and 13 characteristics in my project. Until today, 3 characteristics were working fine. But i added rest of the characteristics and my project...
Hi all,
I am currently using Pyaci serial to establish and test BLE mesh network, and it work fine.
The further step we want to do is to create a duplicated Provisioner...
I have a Thingy52, but no DK. I would like to know if it is today possible to upload a custom firmware only using OTA (no DK), eventually starting from the Nordic Thingy app...
Hi,
I'm trying to transfer data between an nRF52840-DK and an Android phone which has nRF Connect installed on it and I can only reach about 40kbps (that is kilo bytes per...
