Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hi!
Is it technically possible to implement performing of unmodulated TX carrier transmission by a write to some BLE characteristic? If yes, then from what to start?
Thank...
Hi,
I am trying to use the Bluetooth low energy capability of the nRF9160 DK (nRF52840 chip) by using the lte_ble_gateway sample from Nordic. After changing some lines of...
Hi
I'm using ZigBee light control coordinator example in "nRF5 SDK for Thread and Zigbee v3.1.0" on nRF52840 evaluation board.
when it will execute bdb_start_top_level_commissioning...
I am runing the light switch example in zigbee sdk v3.1. I am connecting to a smarthings hub. I have set the a single change on the code:
The device will be connected...
A couple questions about the nRF52840 GPIO Electrical Specification:
1. In the nRF52840 GPIO Electrical specification, VOH at 0.5mA is spec'd to go as low as VDD - 0.4V...
Hello,
I have been using the development kit for more than a month when after one flashing, the LED 5 on the board started blinking at one second intervals and the board...
I read a nRF9160 DK 0.8.5 circuit design and have a question about the GPS circuitry. What will happen if I bring the LTE antenna closer to the GPS antenna and reduce the...
Hi,
We have a program that uses the radio driver for IEEE 15.4. Currently we do not need Bluetooth and IEEE 15.4 working simultaneously but we do need Bluetooth DFU. When...
Hi,
Just spent a while debugging this and since there seems to be nothing - well I can't find it anyway - up here thought I should document this issue. This relates to SDK...
hi ...
i am using nrf toolbox (ble uart )to receive data from nrf52832 ..i am receiving the data for every one minute . i am facing the issue in auto connect see the below...
Hi,
Actually I am interested in making the custom design Board for the nRF52 series , so where can i find the schematics , layout files of the nRF52 Development Kit ....
Using s140 for the nRF52840 is it possible to have a BLE multilink connection (up to 8peripherals) with an extended MTU size (around 70bytes)?
All examples that I have seen...
Dear Team,
would a solution like this be possible with nrf91? http://rxnetworks.com/location-io/predicted-gnss-ephemeris/
> a reduction of Time-To-First-Fix from 45...
Hello!
Could you show me an USBD configuration example which works fine with Arduino serial monitor? Because Arduino serial monitor froze when i send a string , but when...
In the nRF52832 (Laird BL652 module) I have programmed.
MBR + SoftDevice from 0x0000 0000 Application from 0x0002 6000 ~ 0x0005 927C
Now trying to program additional application...
