Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v15.2.0/hardware_driver_pwm.html
Where are more docs like this explaining how to use the drivers?
Hello, everyone, I am a fresh guy using nrf toolbox to read UART (52832) logs. Now I installed nRF Logger and try to save the UART log file. Does anyone can teach me how to...
Greetings to all, I am trying to debug the PrnRF Connect Programmer with visual studio code, but I can not find a way to achieve this. They could give me a hint of how to...
we have a linux gateway with an nrf52832 connected via serial port. the gateway communicates with a modified connectivity HCI application on the nrf52. the gateway device...
Hello everyone,
I am using nrf24l01p. It works fine but some times gets hang, doesn't receive data at all. I am sure that this is not the problem of micro controller because...
I am using the original board. Crystal of 32kHz has not been mounted on this. So, I want to use the internal RC Oscillator. In addition, I use a hrs example of nRF5_SDK_11...
From the product spec, I can operate in either low power mode or constant latency mode. It is not clear how much (or what mechanism) compromises the latency when low power...
Hello,
I'm developing an application that is sending data every certain seconds in a mesh network and, in order to reduce the power consumption, I wish the node enter...
i am using latest version mesh sdk 3.1 .. i want to interface two boards and want to check the bidirectional using text message, example if client sending the hello message...
Hi,
How can I Understand why the nRF9160 is disconnecting from the network?
How can I read the modem trace bin file to understand whats going on with the modem ?
Hello,
Do you have a soft device that integrates both Bluetooth and USB on the nRF52840 ?
I want to program a firmware that uses both and I'm wondering if you have ready...
What changes are needed in SDK V15 sdk_config.h so nRF52832 can run on internal RC oscillator?
I am using the BLE UART example, nRF52832 with Soft device s132_nrf52_6.0...
I want to extend the list of known UUIDs with some custom definitions but I am unable to open the Open UUID definitions file.
I tried following the Adding UUID definitions...
When connected with RTT viewer, a pin reset with nrfjprog shows a J-Link Error popup saying:
J-Link currently uses target interface SWD while current debugger tries to select...
Hi!
I want to send heartbeat messages from 30 servers to 1 client/provisioner.
I can send _HEARTBEAT_PUBLICATION_SET to every server like OpCode = _HEARTBEAT_PUBLICATION_SET...
