I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
It works with SDK v12.3 and soft device 3.0.0. Does not after porting to 15.2. This is a custom board (extremely common configuration with single 32Mhz crystal) that serves...
Hello,
(I also create an issue over Thingy SDK GitHub page - #29)
It seems to me that there is an issue about the usage of MPU-9250.
I motioned Thingy and I observed...
Hi,
I am trying to get DFU working on my PCA10040 board using SDK 14.2 and armgcc toolchain.
I have followed the instructions to set up DFU here:
devzone.nordicsemi...
Hi,
Whenever I call `nrf_malloc` with a parameter bigger than 32, the pointer remains NULL. I think it's related to some sdk setting but I couldn't find it.
Anyone had...
Currently, I am working with the Nordic SimpleOnOff Model of the Light switch in the Bluetooth Mesh.
I am good that the light in the mesh can be set on/off after Provisioned...
HI guys,
I am running a beacon based on the ble_app_beacon example. This works fine.
Next, I made a connectable GAP/GATT application to read and make some settings. This...
https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v15.2.0/lib_timer.html?cp=4_0_0_3_51_0_0#lib_timer_debugging
The link to " Monitor Mode Debugging -...
I flashed the Mesh serial hex file on nRF52840 dongle. I can see my dongle on nRF connect mobile application but not on nRF Mesh mobile application. So do I need the development...
I flashed the mesh serial hex file in two dongles and used one dongle for connecting it to the nRF Connect Windows application. The hex files were present in the nRF SDK for...
Dear Sir,
Whitelist(on periperal side) are used for filtering scan requests( onlly allow the scan requests from the devices whose address is there in the whitelist with...
I'm using ble_app_uart example.
The board go in low power mode, but after 3 minutes (#define APP_ADV_DURATION 18000 ) go OFF. I need that remain in advertsing mode always...
I was developing an green house system for plants which was based on nRF51822 SoC. The system was fully completed and working fine except one problem which was reset of nRF51822...
I am trying to find the optimal way to automate some tests that I run on my BLE device. In this test, I need to write a specific hex value to a custom BLE characteristic of...
Hi all,
I am working on a project and use DWM1001-Dev. I think some of you may have an opinion about my problem because DWM1001 have nRF52832 microprocessor. I'm trying...
