Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hi,
The opcodes for Generic Power OnOff models are wrong. They weren't changed when the model was copied from the Default Transition Time server Model.
From the Model...
Hi，
My english is not good, please forgive me.
msd and hid device，set as follow:
//msd-------------------------------------------------------------
APP_USBD_MSC_GLOBAL_DEF...
Hello,
i'm practice beacon on 51422 DK. The first thing i wanna try is GPIO setting. What else i have to write or replace from the beacon example after setting GPIO in ...
Hi, I have working firmware for nRF52832 dev kit based on mesh coexistence examples (Mesh SDK 2.2.0 + nRF5_SDK_15.0.0). I'm trying to port the same firmware on nRF52840 dev...
I have flashed the firmware using nRF connect app. I have a bat file which executed few commands. I want to transfer that file to flash memory and access it I the file explorer...
Hi there!
I am trying to add custom UUID's for my BLE application.
I have a custom service which has 2 RX and 3 TX characteristics.
I have a situation where the Android...
Hi,
I would like to disable TWIM peripheral when not needed to save some power and enable it just before it's needed. Is there any delay after writing to NRF_TWIMx->ENABLE...
I want to get vdd without timer
so i found this.
https://devzone.nordicsemi.com/f/nordic-q-a/38239/nrf-52832-saadc-without-timer/147517#147517
and change some part like...
I have a design, using the NRF24L01+, that I would like to run from batteries. The Transmitting device is not a problem, because it can turn off when not transmitting.
For...
Hi All,
For NRF52 is that possible to configure the system to use a different pin for RESET than GPIO 21? We want to reset the NRF on errors, if our other MCU detects some...
Board：PCA10056 （0.9.3）
SDK：15.2
Softdevice：S140
Example：ble_app_blinky
Today，I follow this page Using an ampere-meter for current measurement to measure the current...
Used SDK: 15.2.0
Hello,
I want to print some debug messages over RTT after an error occured. After that I want to reset the system.
If I put the string into the que...
I've followed the steps to set up the SDK.
When I execute the batch file(setup_sdk.bat), there is something wrong occur (as below pic)
I've installed the git and add...
