Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
hello, i am implimenting ir with nrf24le1 but after adding the transmit.h,transmit.c nordiac_common.h and lib_ir_common.h the code is compiled successfully but it shows this...
Before(SDK11), I enabled uart and used printf function to print out log message to UART.
But, in SDK12 I can not see printf message. But, app_uart_put is working.
Where...
Hi
I've to provide support to an old project created with SDK 6, under GCC and Eclipse platforms. I've never had problems when creating the HEX file to be used on DFU service...
Just want to check if NRF52832 or NRF52840 can communication with iPhone 7 as instead of W1, which can transfer the data and audio from iPhone to earphone base on NRF52832...
While creating my own service I used ble_app_blinky as an example, once I opened ble_lbs.c file I saw it contains the service's declaration inside the macro:
#if NRF_MODULE_ENABLED...
I'm using nRF52 + SDK11.0.0 + s132. I have an SPI slave configured. I have 40B data being read by a master every 12ms at 1MHz SPI clock. The master is trigger to do the read...
HEY
I am using my nrf 51 dk too program the nrf51822 board externally. How I can identify the board in keil, only the 51 dk is shown in the debug settings. How i can select...
I would like to see output from NRF_LOG_DEBUG in the Rtt Viewer, to achieve that I changed (in sdk_config.h)
#define COMMON_CONFIG_LOG_LEVEL 4
#define NRF_LOG_BACKEND_SERIAL_USES_RTT...
Hi all!
These days I've developed a custom SAADC + UART program to fulfil my needs using the SAADC example in the SDK 11. I've tested it and all is working really fine...
I have 1 dongle and 2 NRF52DKs attached to my computer at the same time, when I am trying to use Keil to program just 1 board it seems like attempts to access all 3 my boards...
NFC examaples in SDK 12.2 and 13.0.0-1.alpha on nRF52832 (board PCA10040) may not work if HAL_NFC_FIELD_TIMER_PERIOD is set to a value higher than 255. HAL_NFC_FIELD_TIMER_PERIOD...
To my very limited knowledge, it has something to do with an "attribute table" of some sort. So you will have an init function, where you get to write all your attributes...
I use active scanning ，the observer will send a scan request when it hears and advertiser, and will listen for a scan response.I only see the scan event，but sent request and...
hello in nrf51 sdk, nordic has already ported freertos.
but if i want to port myself. can anyone tell me how to do it??
first i downloaded freertos from website. but then...
