if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hello,
I am trying to flash the nRF9160 application(merge.hex) which is created after build in an external board. The external board is from fanstel - BLG840F.
Couple...
Hi,
i've been trying to implement gnss functionality on my nrf9160dk board but it didn't work since i was doing it indoors, i've been advised to use an external antenna...
hi support team,
our ncs2.6.0 demo /samples/net/udp is supporting 7002dk, the demo works for 7002dk.
however it doesn't support 52840dk with 7002ek shield,i have modified...
Hi! We have a custom board and when ordering a new version we now get Errors on two of the 18 prototypes.
After trying on another machine with another JLink one of the two...
Hey, I have been trying to get to the root of additional current draw when crypto drivers are enabled.
Without the crypto drivers enabled the current draw between two advertisements...
Hi,
We are working on our manufacturing process that involves use of the nRF9160. I need a way to programmatically get the IMEI and ICCID in order to register the device...
I'm running a nRF52 device that's built on nRF5 SDK11, and it's remaining that way now due to regulatory reasons. My application needed to be updated to support bonding, and...
I have a nRF9160DK board running asset_tracker_v2 on a nRF9160 custom board. V1.7.0 loads and boots fine but when I use V2.5.0 the boot fails as shown below. The only change...
Hello, per the product specification, I see that the nRF52832 CIAA variant requires a shunt 1.0pF capacitor and series 3.3nH inductor.
Is this recommended regardless of...
I have configured NRF52840 as coordinator ,EFR1 (ENDDEVICE) and EFR2(ENDDEVICE) as end devices. These 3 devices are connected in network.EFR2(End device )continuously sending...
I would like to understand the issue of frequency offset calibration in RF signals, I have viewed the
Case ID: 309794
nwp_006.pdf
I would like to know if I can do...
Hi,
We are working on BLE MESH using nRF52840. We are trying to put nRF52840 into deep sleep mode. The deep sleep current is about 210 micro Amp. Further, the current is...
Hi,
I have a coap server/client system and when I send a provisioning request from the client I can see the server is sending the reply. But my 'on_provisioning_reply (...
Hi,
I'm using SPI4M on nRF53 and came across it's errata, but I didn't get where to call the workaround functions.
The workaround is to call the below line upon enabling...
