Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hi,
I'm developing some projects with the nRF51822 chip and I am not able to debug them successfully any more. However, I have previously debugged correctly some projects...
Hi
I am using NCS desktop application
I ported it to my custom board(52833)，It works well
but now，my custom board has three leds，while nrf52 kbd board only has 1 led...
I need to build a simple BLE dc motor control with a potentiometer to provide the rotational position of the motor.
Anyways, my first step is understanding the Nordic libraries...
I am new at Bluetooth. I want to design remote media control(volume up,volume down, play/pause, next track,previous track) and call answer or reject. I have tried to make...
Hello there,
I am encountering an issue with the zigbee light_control example on the SDK v3.1.
Before I explain the the problem, here's some detail about the system setup...
Hello,
I am attempting to retrieve a device's own MAC address and print it out. So far I have encountered two different functions that can help me achieve this.
void zb_osif_get_ieee_eui64...
Hello
I'm working on the example of app_uart in sdk v17.
I'm trying to create a button 'Long Press' feature, but somehow the button input isn't working properly.
Below...
The example app_onoff.c shipped with SDK For Mesh 4.2.0 (unchanged from 4.1.0) have two unused variables in its state struct.
The value_updated variable looks like a left...
Hi
Is the GPIO on the nRF62840 5V tolerant?
I see the VDD supply is capable of 5.5V.
I’m running a 5V Hall effect square wave into the GPIO pin used as an interrupt...
Hi Team,
I would like to send 10 bytes of data in mesh from one device to another device. As i know that we can send data from one device to another device and the packet...
Hello,
I've asked this question around 6 months ago. Now I have to pick up where I left off and I was wondering how much the situation might have changed since.
- Last...
Hi there!
Okay, I've been trying a lot to figure this out, but without any success. I have absolutely no idea what could be the problem whatsoever. The problem is that the...
Hi,
Currently we working on a project that uses:
nRF9160
Zyphre OS
Segger Embedded Studio for Arm (Nordic Edition) V4.52
SDK v1.3
CONFIG_MQTT_LIB_TLS ...
I am currently unable to flash any new code or to erase the flash memory of my nRF52840 Preview DK boards.
I am using SES and the OB J-Link, but also tried JLinkExe and...
Hi, I am using the TIFS register of the NRF RADIO to define the interframe spacing timing. (Done with the following line)
During a 1Mbit or 2Mbit connection, the real TIFS...
