Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
I have been having issues of when I operate some components in the system the nRF52832 goes into a hard reset. I have seemed to fix a lot of the hardware issues but there...
NRF_LOG_INIT HardFault in balloc (see stack trace below).
Code works perfectly without bootloader. However, when the bootloader is present it seems to already have initialized...
I followed some code I found for setting device name. Right now it just transmits as N/A for the device name. Any help would be appreciated.
Here is my code:
/** * Copyright...
Hello,
I am new to Nordic and started using nRF52832. We started a new project. It requires
Act as Peripheral (Single role) only.
Only Advertisement for 3 minutes...
I find the combination of both EasyDMA and non-EasyDMA, plus nrfx and legacy driver in SDK 15.3.0 quite confusing. Where is the implementation of the legacy SPIM (EasyDMA...
I'm using nRF52+SDK11.0.0+S132 . I have a library compiled with GCC using flags -mcpu=cortex-m4 -mfloat-abi=hard -mfpu=fpv4-sp-d16 that I'm trying to link to an application...
Hi,
i am developing an based on NRF52840 and i need to save some credentials and keys in a secure storage and keep them in power cycles, there is any secure storage in NRF52840...
hello,
we are interesting in some of your products and please answer my questions if you can.
we are building a big parking place with private parking lots with individual...
I have been developing a bluetooth application that extends the ble_app_uart example, in SDK v14.x.x, on the nRF52 DK. I've been waiting for a custom built external board...
Hello;
I am working on Audio transfer with microchip and NRF24l01p.
On that, I need to take audio sample and send in very short time.
The PTX side is ok but on PRX side...
I've been going through the nrf mesh Provisioner SDK for android. It has predefined input and output oob models that is selected while provisioning.
Is it possible to design...
Dear,
we have some problems at the startup for our nRF52832 board powered with coin cell battery. The hardware include nRF52832 SoC, an accelerometer (LIS3DHTR) and battery...
Hi,
I'm using nrf52840 with Softdevice. It is not clear to me which memory addresses are both (a) in the flash and (b) are available for the application.
Please advise...
Hi There,
I am working with the nRF52832 and one thing that the software team noticed is that the info.variant we get from the micro is not listed in the data sheet v1.4...
Dear sir,
The current BGA ball size is 0.3mm. What is the recommended VIA hole size for the inner pads for routing the signals out from IC ? or How large of the via in...
