Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
Hi All,
For my project I'm using NRF52832 IC and NRFsdk. I need 2 GPIO external interrupt to get notified. I'm able to configure both pins and able to see the trigger when...
Hello Dev-Community, I have modified the Thingy Firmware for a custom made board which has also the MPU9250 with TWI connected. Everything works fine, if i use RTT Viewer...
Hi,
Referring to this thread -
If the saadc sampling is trigger by a timer (through ppi), what is the correct way to saadc_uninit() without using the global m_sampling...
Hello,
nRF52832 datasheet denotes saadc sampling time in scan mode (paragraph 37.5.4) as:
What is extra time it takes for the easyDMA to store the samples in RAM ? ...
Hi Nordic.
currently i am working on nRF52840 as a reader and after designing as per your recomendation and it is ready to check but whe i connected to the commander the...
I have loaded the HEX file of nRF_Sniffer_200_beta3 to my nRF52832 or nRF52840 board, it can not be run as sniffer. May I know how to use my own nRF52840 chip as Sniffer?...
Hey! Is there a way to multithread the nRF52832? I want to store data in the buffer and do some processing on that. While processing I want to control how the data is stored...
We need to compare the signal of nRF51 dongle with our product.
How to find nRF51 dongle(nRF51422) with hciconfig in Linux?
firmware: PCA10031 1.1.0 2018.39
Guess I...
Hi,
Can you please direct me to the document that explains about generating more than 8 bits of clock in SPI and keeping CS line low for that entire period.
Also, if...
I've been working on a project based on nRF SDK. The project is developed in C++14/17 and I found that nRF SDK 15.2.0 doesn't always want to compile with C++ compiler. I made...
Hi I'm using the nrf52832 and want to send datas via UART and SPI but the PSI example Show different Settings of UART then the BLE_APP_UART. The BLE_APP_UART is running well...
We are currently developing our product in Zephyr using the BLE Host/Controller with virtual HCI (building the project with . We are anticipating a Nordic Zephyr BLE solution...
Are there any native RTOS build-in the SDK? If I need to develop a sensor device driver (i2c based) any recommendation as the safest way to do that. Choosing between freeRTOS...
Hi,
there is a broken link on https://www.nordicsemi.com/DocLib/Content/SDK_Doc/nRF5_SDK/v15-2-0/ble_sdk_app_buttonless_dfu that refers to " Generating bootloader settings...
