hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hi,
I'm trying to toggle GPIOs 32-35 but it can't be done. Other GPIOs though such as 15,21,30 I change successfully.
Here's my code:
I saw a solution regarding NFC...
Until lately, I have never used characteristics longer than the 20 Bytes and if the length of application data was longer, I would fragment it on the application layer.
...
Hi there,
I’m trying to port Thingy to Segger Embedded Studio. After reviewing some related blogs on devzone and github, I have imported the Keil project into SES. All files...
Hi,
I'm trying to use adxl335 accelerometer to detect motion.
I'm having trouble understanding what the output of the accelerometer means.
Obviously, it should tell...
On SDK 12.0.0, SDK 12.1.0 and SDK 12.2.0 only
Please Do not judge the quality of SDK based on number of entries here. This thread should be considered as part of Nordic...
On SDK 13.x.0 only
Please Do not judge the quality of SDK based on number of entries here. This thread should be considered as part of Nordic effort to find issues and...
The soc_evt_handler() function in nrf_drv_clock.c need to set m_clock_cb.hfclk_on = true.
When the softdevice is enabled and multiple modules request the HFCLK using nrf_drv_clock_hfclk_request...
I'm following your instructions for testing the Thread Secure DFU example , but I run into a message "Waiting for NCP to promote to a router ..." at step 6 and I don't o bserve...
I had used the examples\peripheral\blinky\pca10040\blank\arm5_no_packs Keil project from nRF-SDK v15.0.0 using Keil MDK v5.25.
EDIT: as described here: http://infocenter...
Hello,
I am currently implementing an OOK modulation with the nRF52 -DK and therefore I need to start the radio with a carrier on defined frequency. Obviously there is a...
Hello
My English is not very good and please point out if my problem description is not clear. I am building a central project that can connect two peripherals. The template...
Hello Nordic,
we are going to perform RF-PHY test for nRF52810 at DEKRA. Can you help us with IXIT filling? There is one answer available at devzone:
https://devzone.nordicsemi...
hi
i have written a service and added 3 characteristics .In master controll panel i am trying to discover services.i see these logs . Device gets disconnected while discovering...
Running the `examples/ble_app_uart` on below environments, in Nexus6 only, it causes that local name byte array will be broken.
* DK：nRF52 PCA10040 v0.9.0 * SDK：14.2.0 ...
Hello all,
I am working on a college project where i need to interface a SD card, an OLED display along with BLE support on nRF52DK, PCA10040, s132, SDK14.1, Segger embedded...
