hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hi:
I am using SDK14.0 S132 for nrf52832 , i found it's sleep mode power comsumption large than 5mA .
I am using internal LDO and external power is 3.7V li-battery cross...
Hi
Just to be sure: I've recently bought the nRF52840 Preview DK (dev board for nRF52840) but I think I'm going to use the nRF52832 instead for my project.
Is it ok to...
Hi i want to create a new project in Eclipse. I did this my following the complete code form git hub for devzone.nordicsemi.com/.../
*Nordic has provided sample code for...
Hi!
I've based a new project for the nRF52840/S140/Preview-DK on ble_central/ble_app_uart_c .
I use the NRF_LOG_XXXX macros for debug and they print fine in RTT Viewer...
Hi,
I have two nrf51822 device, on work as GAP Central, another work as GAP Peripheral.The two device use different connection parameters, after the connection is established...
hello,
i have developed one board using nRF52832-QFAA and trying to dump simple LED blinking code in it using nRF52 DK board. But code is always dumping into custom board...
How do you do
Now need pwm_driver demo5 duty ratio, is there any way to 1/6 or 1/8?PWM and phase difference is 4 road？
Ask for a few days, change seq_values [], but how...
I am developing firmware using S132 (SDK 11) for a custom board.
After performing Pstorage Update, if I do not wait for the callback from pstorage before continuing execution...
I am currently working with a the nRF5x bluetooth chip family and connecting to a windows 10 device as a central. I am using uart to get some visibility into what is happening...
Greetings -
I recently downloaded the latest SD140 images, 6.0.0-6-alpha, and began having issues with BLE communication.
I'm developing a custom device, based on the...
Hi to everyone!
I have a problem with the NRF_LOG or with RTT Viewer.
I wrote this simple code, just to test an output console.
int i = 0;
while (i< 100)
{
NRF_LOG_INFO...
When a Jlink programmer is connected to multiple devices (daisy chained) how do I specify which device is being programmed on the command line using nrfjprog?
Additionally...
Hi
I am making a speed cadence sensor.
I am using the gpio event handler to check the cumulative wheel revolutions and send the recorded value to the app as a time handler...
Hi,
Once the main hardware init part is done, system idles for a while and then I get a hardfault (APP_ERROR_CHECK returns fatal)
I reset the chip, and asked it to continue...
Hi,
Currently i am trying to understand the gazell api using the nRF5 SDK v14.1.0 example gzp_dynamic_pairing. Within my process to trying to understand the gazell api...
