I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
Just two questions regarding the new nRF52840 to make sure I've understand it correctly;
For the NFC, this is passive only? So it acts like a tag and is not able...
I've been trying to for two days. Using nrf52DK, SDK12, no SD, Keil5.
All I want is to get printf() to work over ITM/SW/Debug, I'd even accept RTT if I had to. I can't...
Hey I am trying to create a blinky project from scratch on
System: MAC OSX
Eclipse Neon
GCC 4.9
I am trying have it eclipse managed make.
I am at a point when after...
Hi, I was wondering If I need to wait for a response from the server that a command was executed before executing another command or if the BLE stack takes care of this under...
Hello
i m searching for a method to send a big buffer with TWI to a slave. The Buffer is read from flash. because its a soundfile its needed to send the buffer without delay...
I am trying to set up a nrF52 -> Rpi v3 -> Exosite through CoAp as in the nrF5 iot sdk. The nrF52 to rpi works as I am able to ping the nrF52 through its global link address...
Hi,
I am writing a code base on the reference manual of nRF51422. In section 29, UART, I don't understand the differences between TASKS, EVENTS and REGISTERS. Aren't they...
Hello!
I'm trying to use the ram_retention in sdk 15 alpha to retain RAM in system off mode and do some power profiling.
The default code seems to retain 8 kB of RAM...
My project needs to use 2 different TWI instances and 1 SPI instance. I knew that it is not possible to use three instances at the same time in nRF52.
To implement 2 TWI...
Hi Nordic,
I am trying to enable the DC/DC converter on a PCA20006 rev 1.3.0.
I am using the softDevice S130.
1. Using the sd_power_dcdc_mode_set(NRF_POWER_DCDC_ENABLE...
Hi.
I am using saadc example code or SDK V13 with the following requirements:
Voltage input up to 70mV,
Resolution: 50uV
So I did some modification to support...
Hello,
yesterday I got a Thingy:52 device at an event held in Frankfurt/Germany. At home I've tested the DFU for the latest firmware and observed that the image was transfered...
Hi,
I’m having some troubles with example code : ble_app_uart_s132_pca10040. The code compile well in Keil and I can prog it in the nfr52 but it doesn’t run. When I check...
