Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
I am beginner of 52832. Current software is based S132 4.0.2 and SDK 13.0.0. Test platform is based on PCA10040.0
My problem is application can not start normally in merged...
Hello,
I am using nrf51 and sdk11. I have one code and I am trying ti build hex or bin file for this code. Now the code size exceeds and so I am trying to build using makefile...
I am learning about FPGA. I have question general question related to it.
Doc1.docx
A FPGA is connected to a 14-bit DAC and to an output amplifier. The DAC have a sampling...
Using S132 v4.0.2, is it possible to disable DLE (i.e. make it NOT set the LE Data Packet Length Extension used bit in the LL_FEATURE_RSP)?
Alternatively, is there a way...
experimental_ble_app_multiperipheral_pca10040_s132 connectivity issue.zip
I’m getting an LMP Response Timeout disconnect reason about 50% of the time when trying to get...
Hi guys
I have been working with a nordic ble device (NRF51822) configured as a Beacon. I am implementing an IOS app, using Apple framework " CoreLocation". My goal is...
I'm looking at using an nRF51822 in a Gazell or ESB application. I prefer not to have any softdevice loaded at all.
What is the correct procedure to perform clock calibration...
Hi
So far I have been using the examples from Keil 5 pack installer.
Now I tried loading some from the SDK example folder and I have issues with includes.
What do I need...
I included button less DFU service in the proximity profile example.When i compile i am getting the following error.
..\..\..\..\..\..\components\libraries\bootloader\dfu...
Hello,
I am working with the example "experimental ble app cgms" in SDK 13.0 and using nRF52832 DK.
when a connection was settup and pairing completed, the CGMS sensor...
I want to ask general question about antenna designing as I am designing antenna to be used with NRF52.
The picture attached with this message shows a printed antenna coil...
At the moment I'm sending a notificaties during the BLE_GAP_EVT_CONNECTED event. This sometimes results in various errors but I can take care of those. The issue I'm having...
GerberVINR-178.zip
SchematicVINR-178.pdf
Bottom layer
Top Layer
IC on the PCB is marked as follows: nrf51822 QFAAHO 1627WM.
I am able to program the custom...
