I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
There have been several topics on limitations on ADC sampling rate when BLE is in connection.
However, I didn't see notes applicable to the following case:
nRF52832, sampling...
Hello all,
I have some troubles to initialize the micro SD card with my custom board.
I have used the nRF 52 DK to write a basic code and do some test. For micro card...
I am using nrf52832 DK and am unable to build my light switch example. It throws an error that some files are not included. In the screenshot, you could see the error. I have...
Hey Everyone
I have written a code for using lora rn2483 with nrf52840 using the uart protocol which is configured on 7 and 5 pin. The program was working fine untill i...
Hi,
I am using the nRF52840 DK and the wireless_uart example from nRF5_SDK_15.0.0 to try and receive data from other 802.15.4 sensors. Using the example I can receive messages...
Hello everyone!
I'm very shy to ask probably a stupid question, but...
I'm trying get abitity to change pwm signal via ble.
I've created service, characteristic, then I...
Hello,
I am trying to get a low consumption and I detect that the activation of the ADC increases the consumption. So I am trying to configure the ADC and when I make...
NRF52832 / S332 / SDK 14.2
Step 1: connect to mobile phone as Peripheral Role, and the connect handler of service was #0 that equal to Peripheral-connection handler number...
Hello,
We are using nRF5 SDK14.2.0 and soft device s132, and trying to perform DFU of the Bootloader itself.
The process fail in nrf_dfu_postvalidate() due to wrong HASH...
i am trying to Connect a custom board with the nrf52 over the bluetooth. nrf52 is running with the BLE_nus
.i am trying to connect it with the uuid in the program is like...
Hi. I`m trying to connect two Nortdic Thingy device and receive data in same time(ex. temperature, humidity etc..).
In my application, I can connect two devices in same...
I have most of the SDK up and running with my firmware, but I cannot find where to limit the number of bonded devices to my module.
I could live with just deleting all the...
Hello,
Is there a way to get the output log for the Mesh Light Switch Demo to output over UART instead of RTT? We are using a Fanstel BT832X module containing an nRF52832...
Hello,
I am currently trying to implement SAADC sampling from three channels into the same sample buffer (device is a 3-axis accelerometer, ADXL335). The root objective...
Hi,
I am working on a project in which we have a sensor connected to the NRF52832.
I am having problem to detect the interrupts sent by the sensor.
The interrupts...
