I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hi,
I'd like to check the battery level in my BLE device, and I can set a timer to handle the checking, however this means that Timer 1 would need to powered up, and hence...
Hi,
The situation: nRF51 has established a connection with the iOS/Android (custom made)App. The nRF51 goes out of the Bluetooth range. Eventually, the Bluetooth connection...
I have looked around but have been unable to find doc explaining this. If there's something around, I'd truly appreciate a pointer.
I have an existing (solar powered) device...
Hello,
i'm searching for informations about calibrating the SAADC of the nRF52. And i have read here: Link
For nRF52, there are no calibration
values that I know of...
Hi Sir/Madam
I wrote a small program for low current verification on nrf51822 development kit with starter mother board.
The program is based on "blinky_example" project...
Hello to all,I have developed a board using the NRF51822;
Currently I am using SDK v11, S130 v2.
I have a problem in my bootloader, since bootloader_app_is_valid (from...
Hi, i want to jump from my app to the bootloader, i used the function
void bootloader_app_start(void)
{
vMBt_eStopAdv_Exe() ;// Stoping the BLE ADV
sd_power_gpregret_clr...
I have a question about when the application is erased during serial DFU single-bank update:
According to the S110 Serial HCI documentation , the serial update packets...
Hi,
I just purchased an nRF51 sniffer. I have set everything up as per the UM. When I invoke the sniffer application, it says scanning for devices, but nothing shows up....
Hello.
I'm investigating how bootloader works (bare minimum), especially how it brings control to an application (already flashed at 0x1B000, s130 SoftDevice also present...
Hi,
I'm creating a simple SPI bootloader without SD for nRF51822 based on this post
The bootloader is connected to Freescale 22F through SPI and it will be without any...
Trying to build the examples for the NRF52 and ant. I have the latest download of SDK11 (nRF5_SDK_11.0.0_89a8197)
It looks like paths are broken as well as missing the ant_interface...
Hi,
I want to communicate with other chip on UART.
the chip on other end requires AT(CR,LF) command to start communication over UART.
UART is setup correctly, but it...
hi guys,
So i made a board with an nrf51822 chip (256kb ) and some sensors + RTC(realtime clock).
The RTC will generate an interruption every 1 minutes. During the interruption...
