Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hi,
I'm developing some projects with the nRF51822 chip and I am not able to debug them successfully any more. However, I have previously debugged correctly some projects...
Hi,
I have been debugging with Serial LTE Modem(SLM) without an external flash .
I made the circuit of nRF9160 (SICA) without the external flash (MX25R6435F?) , I would...
Hi All,
I am using nRF Connect SDK v2.7 + VsCode + NRF5340 DK and trying to add and extend matter-light-bulb sample. With ' MA-onofflight ' when I try to compile the project...
Hi,
I am working on nrf52840DK with NCS v2.7.0. I want to send the data to the addressable led strip using the pwm interface.
I am using the NRF PWM driver ( nrfx_pwm...
Hi there
Does anybody now if there is a implementation / reference project / company which solves the firmware over the air update of several devices inside a OpenThread...
I am having nrf52833 module where I need to update the firmware via uart, I am using sdk_16 and I'm unable to find the PCA10010 for uart. Can anyone suggest me how to attempt...
Hello,
I am currently developing a project using the nRF 9151 and SDK version v2.7.0.
The issue I am facing is that I have configured the PSM mode, but it doesn't seem...
SDK v2.7.0 nRF5340-DK with nRF7002-EK Matter samples (e.g. light bulb) Extra CMake arguments: -DSHIELD=nrf7002ek Use sysbuild
Tested with v2.6.2 (no sysbuild), and it...
hello ,
some brief about my board it is nrf ble nrf52810 without crystal.
i am using segger debugger.
while doing step by step execution it come till line sd_softdevice_enable...
Hello！
I am using the development board of NRF5340DK, I found an external flash (MX25) on it, I want to know how to program the external flash through the onboard jlink...
Hi, our design makes use of nRF52840 MCU. Power is supplied to VDDH pin from a Li-Po battery which can range from 2.5V to 4.2V. Internal REG0 is used to regulate voltage down...
Hello I want to add an extra config file based on the option in prj.conf or in Kconfg. For example: CONFIG_WIFI_SCAN_ONLY=y include the overlay-nrf7000-wifi-scan-only.conf...
Hello,
When I upload the Matter Weather Station application to my Nordic Thingy:53, I encounter a problem.
I am trying to use Google Home to read sensor data, such as...
Hello, I have a custom development board using the 52840 chip, with two LEDs and a serial port connected. It worked well when developing with nrf5 previously. Recently, when...
Hi,
I am using nRF5340 DK and nRF SDK V.2.6.1 for my project
While compiling the custom project in nrf vs code , I am getting the following error;
Configuring incomplete...
