Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
EDIT: We found the reason for this and it is a hardware issue. This question can be deleted as it is no longer valid.
-----
Hello,
We are currently developing a...
Hello,
I would like to obtain some information on the possible substitutes for the nRF51822 (BGA Packaging).
I received notification that right now only the final orders...
I am using the nrf9160 for an OTA firmware update application. I initially executed the fota download file from the http_application_update sample project in it's default...
Hi:
I am trying to get continuous notifications using pc-ble-driver with 52840 dongle from a Nordic NUS board. I set the MTU size to 240. After getting 9 notifications...
Hello, I want to modify ncs\v2.2.0\bootloader\mcuboot\boot\zephyr main.c code of BLE OTA bootloader, but I need to move its code inside my application firmware repository...
Hi,i use nrf52833, I configured P0.05/AIN3 as a NOPULL INPUT(nrf_gpio_cfg_input(5, NRF_GPIO_PIN_NOPULL);), But I found a weak low level in this IO port. What is the problem...
I am using a nRF52811 with nRF5 SDK 17.1
I have set the PHY to BLE_GAP_PHY_CODED, I believe this uses S=8?
Is it possible to select S=2 with this SDK?
Thanks
Hi,
is it possible to build the nRF5340_audio application for the nRF5340-DK?
What I'm currently is investigating is the possibility of finding and connecting to other...
Hi,
I am software engineer working in Philips.
I am trying to transmit 21 bytes of our payload data (fixed payload length).
I have the following configurations done...
I am attempting to connect a nRF52840dk to Azure IoT Hub using OpenThread and TCP. I combined the azure_iot_hub and azure_fota samples into one project, which ran successfully...
I tried to find simple examples to use SPI in nRF9160DK but all the examples has issues. I did connect using raspberry pi to my modem with no issues but when I use nRF9160...
HI
I had some great support in t his ticket so I will try my luck again.
We want to migrate our application from SPM to TFM. We use SDK 2.1.0. We communicate with the...
Hello to all I am quite lost, I need help to connect an oled to my project. The rest of the stages I have it complete, but my experience with OLED, is limited to arduino with...
Hi,
I am looking for help, we are moving to the 3.2 of zephyr. All our projects are custom boards that run on the previous zephyr version (2.5).
When we compile our...
We use nRF9160 with our board (with Serial LTE Modem 1.9.1). We try to download SLM / Modem firmware via nRF Cloud and we ran into several problems/misunderstandings: 1) First...
Hello,
I can get the distance between four NRF52833 device based on the distance measurement toolbox SDK 1.9.1, but the output rate is a little slow, less than 1 Hz. And...
Hi,
I have a custom board based on nrf52811 and nrf9160. So basically I want to flash those 2 custom board. But I only have ST-Link v3. After doing some research, I only...
Hi Nordic team
I work with 2 NRF5340-AUDIO-DKs (LE audio) and now switch to custom HW on the sink side. Since we only need 3W stereo output we work with 2 MAX98357A
We...
