I have been testing the thingy91x and measuring power consumption trying to reduce it to the absolute minimum.
Using a test program that moslty sleeps ( using k_sleep()...
Hello,
I'm working on a project using the nRF52840 and Zephyr, and I'm experiencing an issue when trying to use device power management (PM) with a custom sensor driver...
I am trying to get the wifi stack to connect to a wifi AP using WAP2 Enterprise (initially just with identity and eap_password, later with full ca_certificate check and client...
I've got some timing-issues with the nPM2100. As I could not locate the relevant information in the datasheet, I'm requesting this here.
My PCB has an nPM2100 with a mechanical...
Hello
I’m aware that this topic has been discussed in several posts from a couple of years ago, but I haven’t found a concrete solution yet.
I'm currently using an external...
When my peripheral calls sd_ble_gap_phy_update, setting rx_phys and tx_phys to BLE_GAP_PHY_AUTO, I receive the BLE_GAP_EVT_PHY_UPDATE event with a status of BLE_HCI_UNSUPPORTED_REMOTE_FEATURE...
Hi,
I recently checked support of MCUBoot validation and from NSIB for nrf54l15. (sdk 3.0.0 and above)
During this, I enabled Signature algo as ecdsa-p256.
And...
Hello,
I am working with the nRF-SDK-for-Mesh v0.10.1 I am able to compile and run everything fine. However the DFU example hangs. It looks like a hard fault ( all the...
Dear friends,
As shown in the pic below, my nRF connect won't start. Automatic firmware detection and programming are done.
nRF Connect: v2.2.1, board: PCA10040 AND PCA10036...
When i klick "Erase all" in nRFgo Studio, i allways get this Message
"unable to find or open JLinkARM.dll"
i did already try several hints from this site.
corrected...
Hello,
I will post this question to NDZ first time .
Our customer is in trouble to reduce power consumption at nRF52832.
Our enviornment is below.
CPU: nRF52832...
I am using the ble_app_uart example as my base on a 52840 with sdk 14.1. I have commented out BLE_ADV_EVT_IDLE case in on_adv_evt() function and the BSP_EVENT_SLEEP case in...
Hi:
I download the google official example "android-BluetoothLeGatt" from github
In the original code, the SDK26 is used, but it can not find any BLE device.
If the...
hi, i'm newbee in BLE,now i have a trouble about advertising in NRF51822.
in my project,after BLE disconnect, I can't see BLE again that mean BLE can't advertising continuously...
Is there a good Mac log analyzer for Android's btsnoop_HCI.log file?
I'm trying to debug an Error 0x81 (GATT_INTERNAL_ERROR) that is being returned when I try to write...
Hi, all!
Sorry, I'm not good at English myself.
My device is nrf52832.
Example code is ble_app_uart (pca10040, s132), I did not modify the code.
My problem.
Ble...
I'm working on a custom board based on the nRF52832. I'm developing on Win 8.1 using SES and a J-Link Plus. SDK version 14.1.
I'm trying to follow this tutorial here devzone...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
I am planning to use MDBT42Q with Chip/Ceramic antenna. I can see in the data sheet they have mentioned an optional 32.768khz crystal.
see page 32 (8. Reference Circuit...
