Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
Hello,
I would like to develop a temperature logger which Starts to log temperatures between certain limits
The data is stored until the device has connectivity to the...
Hello,
I know this issue has been discussed extensively in different posts, and I believe I read all of them, but still I can't get it working.
I'm trying to drive...
Hi,
I'm trying to run the i2s output sample from NRF Connect SDK 2.7.0 on the nrf52840 DK, and I'm only getting the clock signal from P1.15, and no signal from any of the...
I'm just a bit fuzzy on how all of the bootloader stuff comes together.
Our application is small (100K-ish), so a dual-bank strategy seems appropriate.
It uses a proprietary...
Hi.
Could you please tell me how to trigger an interrupt when changing the USBREGSTATUS register?
I can monitor the state of this register in polling mode, but I don't...
We used two different packages of 833 and assembled two batches of PCBs. The first batch used the aQFN package, and the radio can operate normally. The second batch used the...
Hi,
We are using nrf Connect SDK v2.0.2 with the hci_rpmsg app programmed into the network core. We have a second radio test DTM application programmed into the network...
Hi, I have used nrf5_SDK//examples/ble_peripheral/ble_app_hids_keyboard & ble_app_hids_mouse both examples with my nrf52840-DK this device is visible in my mobile and laptop...
Hi,
I have a custom nRF9160 board. ADXL362 & MX25R64 share the same SPI bus. I'm trying to validate it individually and looks like there is no communication between both...
Hi.
Board : nRF52840 DK
SDK : NCS 2.0.0 (zephyr) or SDK 17.1.0
I test qdec example.
if I set sampleper value 256us/128us, NRF_QDEC_EVENT_SAMPLERDY Event is not raised...
I am recently trying to get up and running with the nrf9160-DK and have been unable to flash the board successfully even with the Quick start (v0.2.6) app in nrf Connect....
I wanted to try getting all 3 outputs on my nRF5340DK. I tried following the instructions here - https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/security/tfm.html#manual_connection_to_virtual_com_ports_on_the_nrf5340_dk...
Hi,
We've developed a custom PCB featuring the nRF52840 Core Chip, but we're encountering significant challenges with antenna performance, resulting in poor range during...
Hi,
We are using the nrfconnect for thread and zigbee 3.2.
We have modelled our Bluetooth peripheral, running on the nrf52840, on the BLE UART example. It connects fine...
Hi,
1. Can nRF52840 run RCP+BLE at the same time? 2. Are there any examples you can provide to customers? 3. Are FLASH and RAM sufficient for resources?
Thank you for...
