Hi there is a problem in github.com/.../nrf51-UART-examples
any one can help?
I put empty loop in main, and comment off all ble related int. and I process uart_evt by...
Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hello,
I am currently optimizing the power consumption of an nRF54L10-based project.
While I know that system-off mode is the most efficient, my current implementation...
We are currently evaluating thingy91x connectivity in different locations, using some Simbase multi-IMSI sims and are running into an issue where, sometimes, the modem will...
Hello!
One of our clients requested the certified measured EIRP (Effective Isotropic Radiated Power) values of the nRF24L01+ 2.4GHz transceiver, which is used in our products...
Using nrf5340 with nrf70 on a custom board, using NCS 2.9.0 (and I can't/won't update to 3.2.x as the nrfx4 update breaks all my code)
I want to use the wifi interface to...
I have an application in which there are two high speed sensors consider it as sensors 1 and sensor 2. Both sensors are connected over same SPI lines having different CS pins...
Hello,
For the vias in the exposed pad of the NRF54L, I've read that ideally, the vias should be capped and filled. However, due to trying to minimize cost, I was wondering...
Hello everyone,
after some months, yesterday I used my PPK2. When I plugged in and I opened the Power Profiler App, a pop up required me to update the device firmware. ...
Hi,
We had a nRF52840 DK board developed off Hardware files v3.0.3 build. The manufacturer didn't have any of the MCU or SEGGER J-Link debugger files on the device. We are...
I added a cmake configuration option to CMakeLists.txt, but sending a value through west build does not set the cmake option. Here is what I have done: CMakeLists.txt
The...
I am using an nRF52840 dongle as a sniffer to capture BLE packets in Wireshark. Recently, I’ve noticed that the captured files are approximately half the expected size, and...
Hello,
my nRF9151 DK appears to be damaged or has a power-path failure.
Current symptoms:
No LEDs light up
No J-Link is detected
No COM port appears
No mass...
I'm stuck implementing encrypted firmwares on the nrf5340, ncs 3.0.2., with NSIB and MCUBoot. I got signed DFU to work as described in Exercise 3 – DFU with external flash...
I noticed from the design guide that the voltage tolerance of capacitors C3 and C10 is 10V. Can I choose 6.3V for the voltage tolerance of these two capacitors? Will this...
