I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
It looks like even with the latest SDK 1.6.0, the full modem firmware pre-validation is turned off.
It looks like this is a modem firmware feature, so it would seem that...
Hi All,
I am new in the Dev Zone and apologize in advance if the question was posted in the incorrect section.
I would like to run the Thingy91 as tracker hardware for...
Is there any API (software) available to evaluate DWM3000EVB module on nRF52 DK?
Can we use the API/software available for nRF52840-DK for nRF52-DK as well?
From where...
I am following https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.6.0/nrf/gs_installing.html for installing on Linux.
I have installed SES from 1.6.99 documentation...
I am trying to get use the Zephyr console sample for nrf52840dongle but when I have configured the following in my prj.conf file I get a link error.
When I reload the...
Dear friends,
From this case , we already know that the mesh stack will arrange a new block when the node is reset, so we will get a new sequence number. We will use the...
Hi, dear Nordic team. I would like to use buttonless OTA DFU for nRF52805.
Here is what I did:
Step 1) install all tools
Step 2) Build my ADC code, rename the output...
Hello
I'm going to use 'frequency hopping' to prevent frequency interference.
I don't know what frequency hopping is yet. May I have a good example and related documents...
Hi there
We managed to send/receive SMS on the nRF91Dk using the asset_tracker_v1 example, which contains the at_client.
However, with the asset_tracker_v2 we never...
Hi all,
Here's the context -
Hardware :
- nrf52840 DK
- sensor - LIS3DH connected via SPI
Software:
- SES
- nrfConnect
I need to send data being captured...
I've been trying to write a simple I2S loopback project for the nRF5340DK board using SES. Zephyr's documentation doesn't list I2S as a supported peripheral for this device...
I updated the firmware according to the video "https://www.youtube.com/watch?v=xQ7hDzRULJQ&t=314s&ab_channel=NordicSemiconductor"
File for "update modem" : mfw_nrf9160_1...
Good morning everyone,
I have questions regarding the initialization of UART communication between nRF52 and nRF91 on nRF91 DK.
Device HW/SW setup:
nRF52 DK: Bluetooth...
Hi!
We recently developed some firmware using S112 on a nRF52810 but realised that we needed data length extension, so changed to using S113.
Previously everything worked...
