Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hi,
I am working on the MG996R servo and MG90S with nRF52840.
I am using the following delay logic to operate MG90S. (As per datasheet)
MG90S is working perfectly fine...
Hi ,
Just one question.
I am trying to create services using hrs examples and its useful.
Currently one question I have that ,
the battery indicator is only notifiable...
Using: Windows 10, nRF Connect v3.5.0, nrf v1.3.0, zephyr v2.3.0
I have a board based on the Thingy91 and the Asset Tracker application. I verified serial console output...
I want to quickly send up to 100KB of data to a connected smartphone and then disconnect to save battery.
I have most of this working using the NUS service but today I noticed...
Hi Team,
I would like to perform the DFU without using the nrfutil and OTA update. Is there any way to perform DFU without the nrfutil.
Our requirement is - We have...
Hello,
i built a SPI Master example based on this: SPI Master example
The example is a bit outdated and needed some rework and fix to work. I don't know if i am missing...
Hi.
NRF52832 is used as central for connecting with phones as peripheral. NUS service is used. Lesc is used too.
SDK 17 SoftDevice S132 V7.0.1
I have sometimes crash...
Hello,
From some time now i have been tryng to start developing an app, but i encountered a problem where the board does not connect, or does not find a provider from the...
Hi,
My goal: F lash hci_usb in my nRF52840 Dongle, so that i can use Bluez stack in my Linux host and nRF dongle as BT controller.
Build status: Success
Flash : Failed...
Hello,
I am trying to find the electrical and timing specs of the nRF52832 SoC. Where can I find them? In the Product Specification document they are not given.
Thanks...
I'm looking into the best way to split an application implementing a LwM2M stack over 6LoWPAN between the network and application cores of the nrf5340. I fell like the most...
I have an nRF51 based Bluefruit LE Friend device with the Nordic V3 BLE sniffer firmware installed. I am using the associated Nordic BLE interface with Wireshark 3.2.5 (64bit...
Hi everyone.
I know this is gonna be a long story, thank you for your patience...
I have successfully utilized a few examples in the SDK15.3 directory on my PCA10056...
Hello
I have an interesting problem from the ble_app_uart example modified to work with spis.
ble_nus.c code
In the ble_nus.c code (above) I modified to enable notifications...
