Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
I saw some posts online about using SPI to simulate the timing of WS2812. I thought using peripherals could save CPU time, but I noticed that SPI seems unable to configure...
Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
After attempting to write data to the filesystem, my 125μs timer interrupt (highest priority) is delayed by tens to hundreds of microseconds.
I enabled the following configuration...
I'm having a hard time replicating the config needed to be DFU compatible with a build from an earlier SDK version. Earlier version used only a non upgradeable MCUBoot with...
Hi,
I am working on the channel sounding procedure with the nrf54l15 dk's right now and I have an external antenna that I want to use to improve the connection. I plugged...
On nrf-sdk 3.0.1, we were running nrf54 (main app) with Zephyr's PPP modem for nrf91 SLM. Everything was working fine. After upgrading to nrf-sdk 3.1.0, I am now getting this...
Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
Dear Nordic Specialist,
I am currently testing the minimum connection interval at which BLE Channel Sounding can operate reliably. Specifically, I would like to achieve...
Hello,
I was wondering if anyone would happen to have sample code to activate the accelerometer in the Thingy 91X? If also possible, it would be very helpful to have the...
I'm trying to setup some code to emulate an NFC tag with an NDEF external record based on the NFC tag sample in NCS 2.6.0.
The hardware is a custom board based on the nRF52840...
Hello I am investigating the power consumption of the nRF9151-DK using PPK II. The measurement settings are as follows.
・Connect PPK II's VOUT and DK's P22 VDD_nRF. ・Connect...
I use nrf5340 audio DK, SDK v3.0.2, and added an iso.conf,
A lot of warnings were reported during compilation.
Are these conf not effective?
If I want these conf...
I'm interested in configuring a NR5340DK as an end device on a Zigbee network where the coordinator is a 3rd party device that uses legacy Zigbee. I'm fairly new to Zigbee...
Hello. I'm trying to call an interrupt service routine (ISR) using IRQ_DIRECT_CONNECT, but it is not working.
Here is the flow of my code:
So, it is expected to print...
