Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
I am trying to save rssi data that I print to the command line to a .csv file.
In the ble_app_interactive example in the cli_m.c file, here is my code:
Without the following...
Hi
I have the Adafruit Feather nRF52 Bluefruit - nRF52832 board that I can program it using Arduino via Adafruit library in Arduino without any problems.
Now I have an...
How can I disable all code-optimizing in SEGGER ?
I build and modify some Nordics example-tutorials using nRF52832 and want start debugging.
Best regards Lennart Vedin...
Hi, I was using eclipse for the development of our board using the nRF52832 and when I launch the debug on eclipse, the program does not flash and this is the output that...
When using "nrfutil dfu serial" can it be configured to log all the bytes transmitted and all bytes received in a log file or on the console?
A colleague of mine is starting...
We have found what appears an easily reproducible bug in nrf_serial_read.
Reproduce as follows:
* PCA10040
* SDK 15.3
* SES
* Example project peripheral serial ...
Hi everyone,
I'm working on the nrf52832 using the SDK 15.2.0 with freertos and the application I am developing requires to save data on the flash while the BLE stack is...
Hi
When a GATT Table is created using the softdevice api, how do specify that a service or characteristic shall have a minimum key size of X so that if the current encrytion...
I am currently developing an app on Android studio that should detect nrfDongle.
I successfully uploaded UART software from SDK 13.0.0 to dongle and it is being successfully...
Hello, i want to know is it possible scan iBeacons with a node using nrf mesh with proxy features like the light switch node server example? if this is, how i could start...
Hello.
I have pa/lna on my device. It works properly in application (rssi is about 30 dbm). But when application goes into bootloader (dfu over ble using nrfconnect on android...
Hi, I'm using the nrf connect mobile app and I want to connect multiple devices to the advertising device and I want them all to access the same characteristic at the same...
When I open SES it says that it cannot detect any j-link so it asks me to buy license. But shouldn't my nrf52840 dk board have on-board j-link that SES should detect? I check...
Hi,
as I understand (and tried), in order to get low power consumption on the NRF91, I need to to get CONFIG_SERIAL=n.
However , I need the uart to be enabled (for short...
