Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Heads up for anyone using the IoT SDK (currently 0.8.0). This SDK has the TinyDTLS-0.8.1 embedded in it... and I believe that there is a bug in the TinyDTLS CCM functions...
A new library/toolkit has been built that allows us to invoke the services of an nRF24L01 from a Java environment. Documentation and links to the Github project can be found...
Hi,
I am sending data from Android phone in every 200 ms to nRF8001. But sometimes I found there is a 50 ms or 100 ms delay. It looks like nRF8001 spending some time in...
Hi,
I've been working to get a Ublox GPS module to interface with my NRF52840 DK over UART. The GPS device boots up and starts streaming data almost immediately.
I am...
I am nRF52832 , S132 , SDK15.0.0 // nRF52840, SDK15.0.0 is used.
Examples of esb_prx, esb_ptx are modified and used.
Transmitter : nRF52832
Receive : nRF52840_DK
Senders...
hello
I have once again issues when I want to write a 'long" characteristic e.g. 85 bytes.
1) if I use a smaller MTU e.g. 23 or 50, I received corrtectly the User Memory...
I would like to design a BLE-controlled electronic device. My requirements are:
1- Very low power consumption. (Less than 200uA in IDLE mode)
2- Slow periodic BLE advertising...
We are a module manufacturer and have used the 52810 as a serial port transparent transmission module.
1. Our customer reports that when we put "More service uuid" into...
Hello there,
We're developing a chip with a nRF52840 as the only processor, which we're trying to get certified against 802.15.4. However, we had problems passing the radiated...
Hi,
I made a PCB with nrf52832. In the intial bring up, I noticed its 32MHz XTAL is not up. Then I debugged the PCB and measured the voltages at different points in the...
I have a fairly extensive application built in 12.3.
To add FDS to this I started with 14.2, replaced the logging with RTT and I know I'll have the change the FDS calls...
Hello everyone,
This is my first question ever, sorry voor my bad english.
Im just started to work with a STMF429I discovery board and a NRF52832(isp1507) BLE chip.
Im...
HI nordic
i installed command line tools in https://www.nordicsemi.com/Software-and-Tools/Development-Tools/nRF5-Command-Line-Tools
and i got this exe file nRF5x-Command...
We have a custom board built around the nrf52840 chipset. We developed code against the dk kit of the same now we are trying to get this working on the custom board.
1)...
Hello,
So I need to connect my NRF52 with a LoRa module E32 via an UART connexion, and then I need to send data using this function:
The probleme is that my code work...
Hi!
I have found the following piece of code on an example from a Nordic employee. I'm curious as to its purpose.
Why is the register set, and then read just after...
