Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
I am trying to have the dk (i have the 10036 preview) send pwm signals to a motor controller so that i can direct its speed. I have based a lot of the code below of this utorial...
Hi, I have seen that on mbed compiler, there is a bootloader that include the DFU and with this, we should not implement DFU in application.
In keil, we must implement...
During Power Off mode the nRF52 GPIOs stay retained. But by waking up on a external Pin we can see another Pin toggles for approx. 600ns. It seems this happens during the...
Hi, all.
I'd like to broadcast only when i want to inform nortification.
flow like
No advertising when application start.
Check the events that there...
I'm trying to develop a minimalist android app to send and receive data with my nrf51822 dev-board.
Can anyone please tell me where I can find a great project example?...
Hello,
In our project i am using nrf51822 with stack Softdevice S110 . We want to connect it with Samsung Gear S2.Is it possible with stack s110 or i have to use stack...
When the device powers up I want to grab the device name from a known location and also rewrite that same location when I get a new device name. How can I write to the internal...
Suppose you want to send 20 bytes of data using API sd_ble_gatts_hvx, do you need to punctuate the first 16 or so data within the 20 bytes sent with a CRC ?
it may seem...
Hi, all. I use nrf52 and softdevice(S132).
I'd like to know SoftDevice process timing to hardware.
Can it be ?
I know, SoftDevice Specification in "Processor availability...
Hello,
I have an development kit NRF51 and wrote a code for it which uses uart, ble advertising and ble scan. It works pretty well on the kit.
The problem is when I...
Hi,
I use a personnal GAP Address, but it must be the type used:
-Public address.
-Random Static address.
-Private Resolvable address.
-Private Non-Resolvable address...
Hi,
I am trying to get the dfu single bank bootloader ( github.com/.../nrf51-dfu-single-bank-ble) supplied by Nordic to work. I can successfully push firmware to my device...
Hi, I am just trying to understand the examples properly. This value is mostly set to 0, sometimes set to 1, and used at the call to the soft device initialization.
ble_enable_params...
I'm trying to send some data to a custom event handler function using app_scheduler. The problem I am having is the data I am sending is not being received.
I expect this...
Dir sir,
I noticed that you are using the internal LDO regulator in nRF51822 beacon kit.
Why do you recommend to use LDO regulator for Coin Cell battery?
In addition...