I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
Hi,
first of all i know that this is not a "good question", but my hacker side is trying to... tweak hex file of softdevice 113 to fit my low memory footprint.
I mean...
Hello everyone, I am working on a custom board based on the nRF5340 and need to implement code execution from an external QSPI memory. The board uses the IS25LP128 memory...
Hi, I am working on a project that collects data from various sensors and transmits it to a Mobile application via BLE. Can I use Isochronous Streaming for it? Can I set up...
Hi community! I have custom boards using nRF5340. A couple boards has suddenly gone bad and unable to be flashed or communicated with after a few reflash cycles.
I've read...
Hello
I would like to sign an image temporarily with west CMake options as described in Enabling a bootloader chain using sysbuild using the comand line:
In it's final...
Dear DevZone:
I use NCS 2.8.0 to build Light Switch FW, my build command as below:
west build -p always --build-dir nrf/samples/matter/light_switch/build -b nrf5340dk_nrf5340_cpuapp...
Dear Devzone,
I currently use the nrfutil dfu serial command to upgrade the firmware, which is OK. I want to upgrade the firmware of 52832 through MCU, so I need to know...
Hello support,
We are developing a battery-operated sensor. For that, we are using nrf5340. Also, we made an enclosure for the sensor.
While developing we found that the...
Hi there,
Is switching between UART and I2C runtime on the nRF52840 with Zephyr possible when utilizing the same two pins for TX/RX vs SDA/SCL?
Thanks in advance,
L...
What version of LVGL is used with nRFConnect for VSC 2.7? Where can I find this information generally. It seems like the lvgl version is 8.3, but I don't know why I think...
Hello,
I am writing this thread to ask what would be the hardware configuration for the QKAA version of the nRF5340 chip if I don't want to use the wireless features of...
I am considering using the nRF7002 for a Wi-Fi application. I want to use an nRF54L15 as the host for an nRF7002 and operate it using Target Wake Time (TWT) to periodically...
I need to connect to other units according to their MAC address. I'm assuming that this:
BT_SCAN_FILTER_TYPE_ADDR
Is the thing to use in this:
bt_scan_filter_add...
Hi, I am working on a project where I need to add ble dfu as well as serial dfu issue I am getting on adding serial dfu to ble example I am getting error variables undeclared...
