Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
I'm trying to follow the DevAcademy Intermediate Lesson 5 Exercise 2 using an Elegoo shield instead of the Adafruit one.
The shield I'm using is this one: https://www.elegoo...
Hello, we have built a BLE device based on the 52840 chip and the nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_hids_mouse example architecture. We have built a...
Hi,
1. The customer would like to know which values are configured for which registers of nRF5340 by the following instructions?
nrfjprog --family NRF53 --coprocessor...
Hello!
I am using an nRF52805 for a custom board design and I am hoping to get some advice on selecting peripherals and Zephyr features that would best meet my system...
Dear Nordic
hardware:NRF5340, sdk:2.6.1
Our project needs to use floating-point calculations. Attempting to add CONFIG_FPU=y and CONFIG_FPU_SHARING=y to prj.conf will...
I use GNSS with the timout at 0 and interval at 65535.
I do not really need the location but is it nice to have a kind of a log of it because it is available en power consumption...
Context: We are planning to connect the nRF9151 to a private test network using a coax. cable. for development debugging.
(#1) Do your modules support SIM cards with test...
Good day
I have a lwm2m client running on a custom nrf9160 board. I would like to run everything network related to network on a separate chip. Assuming that the two chips...
Some guidance on this query,please. I have a project with several freestanding application (please check topology below). I would like all the apps to acccess a custom board...
Hi,
I am currently configuring the nPM1300-EK with the nRF5340-DK by following the instructions from the webinar "Adding battery charging and fuel gauging to your nRF52...
For a device like the nRF9160 Feather, you need a second USB to UART device for listening to the modem traces. When I go to select the Terminal Serial Port under Advanced...
Hi All,
Im very new to this how firmware space and would love some help.
Currently i have a NRF52840 DK Board with a Seeed Canbus shield. ( CAN-BUS Shield V2.0 | Seeed...
1. Hi i am using nrf52840 sdk ver 17.1.0 in secure bootloader /pca10056_uart_debug
2. I have flashed the dfu uart code without any change
3. while performing dfu via uart...
We are developing a ZigBee-based end device using the nRF52840. We have implemented most of the functionalities and also reporting and are able to receive reporting information...
I am working on a wearable which has Fanstel BT40F MCU (SOC nrf 5340). when i initially turn on my pmic, it can only generate 1.8 volt from buck 1 regulator and I am thinking...
