Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
I'm sorry. This must be trivial to all of you. I'm a beginner with nrf52 programming, and I saw several examples that refer to timers TASK_START, TASK_CLEAR, TASK_STOP. Everywhere...
Our device has both a 9160 and a 52840 on it.
The 9160 is running the stock serial modem firmware on it.
The 52840 is running a custom handler for AT connection targeted...
Hello,
We are doing some network quality tests on LTE-M with PSM off and notice loss on UDP between 0% to sometimes 15% on simple udp messages sent every 10 seconds from...
It is not very clean to start a work_q with no name when all others name them properly, or at least put in the name of their k_work_q struct. Working with system threads it...
Hi,
I'm upgrading my firmware from sdk1.7.0 and there is one error that i can't solve and need your help.
The code is working on SDK1.7.0, solved all the errors that appeared...
Hi,
I have a nrf5340 device which is built with nrf Connect SDK 1.6. I can successfully DFU over ble by nRF Connect mobile app. Right now, I am trying to do DFU from my...
Hello,
I am attempting to configure a project with full zephyr logs (using RTT backend). I am, however, unable to get the full logs (see example below):
[00013022] <dbg...
Hi,
I have enabled SPIM on nRF52810 and worked normally.But when I enabled on nRF52832, it worked unusual.
I had defined CONFIG_NFCT_PINS_AS_GPIOS because used P0.9 and...
Hello,
We are using lwm2m client project SDK version v1.9.0. We need to enable #define CONNMON_LAC 12 to get LAC value but i am facing problem to enable #if defined(CONFIG_LWM2M_CONNMON_OBJECT_VERSION_1_2...
Hi,
When I download the example of "ble_app_uart"(SDK17.0.2 S132) in nRF52832,mty board is working as normal. But when I add RNG in main, the RTT Viewer just logging SOFTDEVICE...
I have some odd cases where an nrf53 based device just disappears from BLE. It's no longer connected, and not advertising.
I'm looking for a method for the application processor...
We use nRF9160 on our own board. The firmware "Serial lte modem" is installed on the chip with connection to an external MCU. A port is connected to the board to communicate...
Hi,
I use the nrf mesh sdk for long time and I just see that its migrate to zephyr rtos.
After reading the nrf mesh sdk doc and the zephyr project doc, I have some questions...
Good afternoon.
We're using nrf Connect for mobile to perform DFU over BLE to an nrf5340-based module with firmware built using the nrf connect 1.6.1 SDK and its associated...
0 dBm TX @ 1 Mb/s Bluetooth Low Energy mode, Clock = HFXO 7.1 mA
Radio RX @ 1 Mb/s Bluetooth Low Energy mode, Clock = HFXO 6.5 mA
I want to know which example is tested...
