SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
Hi,
I'm trying to configure my LTE modem (Icarus Board + nRF 9160 + SDK 1.7) with an external SIM.
For that i have to use the PDP configuration.
I use in my prj.conf...
Hi,
I am using SES and NCS SDK 1.6.1 under Win10.
A GPS module is connected to NRF5340, using an UARTE to communicate. The pin receiving GPS data is P0.31.
It works...
Hello,
I want to make sensor sleep and wake-up according to VDD.
- When VDD is below 2.8V, Sensor sleep.
- When VDD is above 2.8V, Sensor wake-up.
Since my board...
Hello,
We have a question from one of our customers as to whether the 52833 is compatible with the S340 Soft Device. On the Nordic website, it is not listed as a compatible...
Could someone explain how to power the nRF52840 via USB?
Looking at the schematics, and also reading the "objective" spec, I can see that VBUS is connected to the USB input...
Hello,
Since yesterday's update of the nRF connect extension the device name of the target in the "connected" devices screen is updated from nrf9160_xxAA to nrf9160_xxAA_REV2...
Hi Everyone,
I tried to build lpUart example from samples available. I was trying to debug then I got the breakpoint on
"__ASSERT (lpuart, "Failed to get the device...
i was working on nRF52840 and nRF9160 with NCS v1.8.0.
i'd like to find an API to reboot system. so i tried to call NVIC_SystemReset(). it works in my nRF9160 project. ...
I am currently designing a PCB which incorporates the nRF9160, and I would like to know the devices behaviour in between 2.0 V and 3.0 V, as this is below the minimum VDD...
Dear,
We are working on our custom boards to develop a watch product which need external flash memory connected by QSPI interface. In this product, the UI images and font...
As I learnt, nRF5232 defaut with LDO mode, DC/DC is diabled, but I can not find any config in nRF5 SDK for nRF52 DK,
someone said to use: sd_power_dcdc_mode_set,other said...
Hi,
I've been reading that the nrf9160 can only receive up to ~2KB of data at a time. It seems that the connection terminates if I send too much to the nrf9160. I tried...
Hi again Nordic, I need some pointers. Håkon, a very patient man here, sent me an example code repo of usage of external flash memory on the nRF9160DK. I've tried the sample...
