I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I want to use UART.
I checked the waveform and UART does not send data. Here is my code. build and run are successful. Any help? I connect UART RX and TX directly, which...
hi... how to make a nordic app to act as a peripheral , i have read one post , in that they mentioned set up to be done in gap peripheral mode . how to do that
IAR 7.60
52840
nRF5_SDK_15.2.0_9412b96
Hi there, I'm trying to do some modification in the bootloader (so that we can write the image to the flash's bank1 using our...
Hello,
I read through the Bluetooth core specification in order to get a better understanding of the information that has to be stored at a minimum if using bonding. But...
Hello,
i'm trying to use ble_advertising_init to initialize my advertising data, but when i use this function like it is used in the examples i get NRF_ERROR_INVALID_PARAM...
When I open device just after I plug it in the PC it work fine, but when I try to do it again (exit python script and run it again) I'm getting Error code 13.
Firmware:...
We are currently in the prototype stage using the nRF9160 and are preparing the firmware for the prototype. We have a few question that we hope someone could answer :)
Will...
Hi,
I want to test BLE 5.0 using two nRF52 dev kit. i am using the ble_app_uart example kindly guide me what are the changes to made in this example to connect two kits...
It's easy for me to create make file target but I am not able to identify where and how to add the custom target in the Segger Embedded Studio(SES).
My default build configuration...
Hi everyone. I am trying to find the best way to establish a Bluetooth connection to a nRF52832 in the least amount of time.
I'm designing an ultra low power perpheral...
Hello,
Would it be possible to create a partial code that can be placed on external memory, and loaded into ram for execution when needed?
As I believe it is possible...
Hi,
I am developing a Bluetooth peripheral application using NRF52832 MCU , where in it is used for collecting vibration sensor data for about specific duration.
like...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hello All,
I am new to Nordic and i have nRF52840 development kit. I want to build code/ programm on thread and Zigbee base.
I have downloaded the Thread and Zigbee SDK...
Hi!
I do not know what the problem is.
First of all, I use nrf52-dk and SDK 15.2
And then, i read 'PPK User Guide v2.3'
I use 'nRF Connect > Power Profiler' to measure...
