if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hi,
i am working on RTC to create custom clock to measure time it is working fine but when i initialise ble stack and softdevice and adverticeinit it is not working. and...
Hi,
Maybe someone can point me into the right direction, I'm on S110 and SDK10 for hardware/legacy reason.
I have a pstorage function using init, load, clear and write...
Hi.
I am investigating the cap touch for a while, and I am working directly with the capacitive driver from here.
As being said there and other places, the driver will...
Hi all
What is the minimum required length of a LOW pulse to be detected by the nRF52832 via GPIO SENSE mechanism? I couldn't find it in the product specification.
I...
Hi Nordic Team,
I am using board PCA10040 wtih nRF52832 SDK 11.
I have Added DFU code to ble_app_hrs_freertos example.
Once I will go for DFU from nrf Mobile Application...
Hi all
I was investigating a NMI_interrupt today and found out that it was caused by a race condition in the fstorage module.
The problem may occur after a flash operation...
HI ,
I am using nrf52832 with s132 . I am trying to measure ADC value at some periodic interval. In nrf_drv_timer_init() function , code gets restarting after executing nrf_timer_event_clear...
Hi,
I use bootloader from SDK6 and I have sd_power_system_off() in on_ble_evt in event BLE_GAP_EVT_TIMEOUT and BLE_GAP_EVT_DISCONNECTED. I use SDK7.1 and SD110 7.1.
It cause...
I'm programming an application that uses the NUS, and I'm trying to test my code using the Android version of nRF Connect. I'm using a nRF52832 on dev board PCA10040, and...
Hello,
With sdk13 and app_pwm library, I only got 9bits resolution for 32KHz freq.
The pwm should have 16bits resolution, with max freq 100KHz?
please could anyone...
hi ,all
I feel confused about" out_of_sync" and" in_sync" parameters .If a devece is in sync,how the channels was changed ?And what's the use of"nrf_gzll_set_device_channel_selection_policy...
we builded " BLE to IR " using nRF51822 , it was working fine with out the softdevice.
problem start when we integrated with the SoftDevice .
1.the problem that we need...
Hi.
I am trying to get a capacitive sensor library using a button ( 2 plates, one to ground, one to the AIN, separated).
It's going crazy, sometimes it just get tones...
hi,
I'm designing a board with nrf51822 chip. this board work on 2450 lithium rechargeable battery and it contain an MCP73831T circuit which is responsible of recharging...
