Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
My project is developed on nRF52840, it needs to communication with a mobile device through BLE, nRF52840 is as central. The mobile device starts BLE advertising, then, nRF52840...
hello guys, I want to use nrf52840 for my project is it possible to use ST Link for it. because I don't have SEGGER J-link ,if it is possible how can we use it please let...
Hello
I am trying to connect the nRF9160 -DK board to nRFCloud using CoAP protocol. I have written an application for this case. I tested my application with two different...
Hello
I'm trying to connect nrf7002EK with SPI3 with nrf52840DK,
NCS/Samples/WiFi/Shell, but I came up after Flash
The error shown in the image below
I would like...
Hello,
I'm trying to erase/read an external flash ( MX25L6433F) connected to an nrf52840 using nrfjprog. I've created a .toml file for the configuration, see attached. The...
Hello,
With the nRF5340 LE audio application comming with nRF Connect SDK 2.6.0, I found an increase in the audio latency compared to previous versions. I was able to measure...
Hi,
I'm implementing flashing modul, which will be running on external mcu. Therefore for the very 1st step, I have captured traffic while performing dfu on PCA10040 via...
Hello,
Do you have an example that allows you to use the “Service Changed Characteristic” on the server side?
In fact, I saw on the internet that on IOS, we have to use...
Hello,
I am trying to generate encrypted data of particular data with IV and Key value by using mbedtls functions but when I try to do that in AES_CBC example code I am...
Hello,
I have multiple nrf52840 devices ( PCB's ) that act as peripherals and advertise data in BLE 5, and connectable in BLE 4.
We are able to connect to the device using...
I'm trying to enable DFU on our device but am getting a lot of issues.
I used Device Manager to upload app_update.bin and it worked. If I use Flutter example to upload firmware...
Hello everyone,
I am currently evaluating the nPM1300 Fuel Gauge with a LiFePo4 battery.
I would like to use nPM PowerUP to prepare the battery profile, but it appears...
hi support team,
i was testing mcumgr ota from uart, but found that the speed is slow how can i improve this?
i have change uart baud to 460800, but did not help. for...
Hi,
I'm using an nRF52840 DK to develop my prototype. Now I'm moving into the PCB design phase and I'm using a BLE ceramic antenna. I'll add a pi network footprint to tune...
