I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
Hi,
I just got a ppk2 and I am not sure which wire needs to be connected to where.
I am going to use this to measure current consumption but I've used only extarnal DUT...
Hi all,
I'm starting a project with a nRF52840, and start protoyping with pca10056 board.
I started with compiling ble_app_blinky example app, with armgcc.
I can compile...
My nRF52 device has a connection opened in peripheral mode and in some cases I want to close the connection with reason code "power off", i.e. call sd_ble_gap_disconnect with...
Hi,
I'm reading through the documentation on using the SAADC with the NRF52 kits. The examples are using PPI to manage the SAADC and allow it to sample locationally in...
Dear All,
I need a high frequency clock in order to measure the time between a couple of events. In the RTC HAL there are functions that allow to retrieve the counter...
nordic nrfconnect sdk, wrong bit mask in driver for thingy light sensor bh1749
In the nordic nrfconnect sdk there is a bitmask typo causing wrong anction.
The header...
When running firmware without a probe, interrupts don't seem to work. I'm using a Segger Mini Edu on an Actinius Icarus (nRF9160). I'm using EGU1. When the probe is attached...
Hi,
I am looking for detailed electrical characterization details for SAADC - beyond 1 page summary in nRF52833 product spec v1.3; under 6.21.10.1 SAADC electrical specification...
Is there some documentation listing what C library functions are supported? For example if I use the Keil IDE to look for FILE I find it. But if I look for 'fread' it says...
Hi,
I'm building a gateway using nrf mesh serial, and I want to monitoring devices status in the network by listening heartbeat messages from devices, but when I set publication...
Dear All, We will do a production with over 1000 Nordic nrf9160 devices, for which we need to program the modem firmware (v1.2.0) and the application software. We would like...
Hello, I started learning BLE/nrf about a week ago and I faced an issue that I unable to handle more than one connection simultaneously.
I have a pretty simple application...
Hi,
I am using nRF52832 and SDK v15.00 for development.
I am working in ble_app_uart peripheral example. I have a task where I need to configure another UART communication...
Hello Everyone,
we are using Nordic's nRF52840 controller with SoftDevice S140 and the default Bootloader(C:\nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10056_ble...
Hello, I am working on a nRF52840 and started with the SDK15 gls bonding example. The device has no buttons or display so we are stuck with 1v2. We are hoping to incorporate...
