I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
Using Rigado board, MBD350, I am able to write and test basic application using UART and BLE
using my custome board I get the following error:
NRF_BREAKPOINT_COND; ...
Hi.
I development nRF52832(SDK15.00.00, S132).
I have modified SDK15->examples->ble_peripheral->ble_app_uart->pca10040->s132
I want to unuse uart, So I using app_uart_close...
Hi Sir,
We would like to use 32-bit address flash (MX25L25635F), and we set the " QSPI_CONFIG_ADDRMODE" to "1" to support 32-bit address.
when USB port connect to PC,...
i use the BLE uart example in SDK11.0 to test. I delete the UART hardware init and just use the BLE send data to phone every 500ms. I found whatever i set the MIN_CONN_INTERVAL...
Hi,
I have an issue with a situation where a client remains connected when not needed anymore, I need to terminate any connection that has been active too long, for example...
Hello,
I used the gzll_host_ack_payload_nrf24le project and gzll_device_nrf24le to test the communiction between two nrf24les over Gazell. The result is that the host could...
Hi,
We would like to add another element to the provisioner. Is there an example how to provision and configure a client element on a provisioner node using the new SDK...
Hi, if the setting of the nrf52832 is shown as below:
Is this possible to happen?
cause when I was trying to use the power profiling example to test the connection mode...
Hello,
the current situation is nrf52832 can not receive the ack payload from nrf24le.
nrf52832 is DEVICE ,using the project from nrf5_sdk13.0.0\exzmples\multiprotocol...
Hello.
I need to compile the bootloader for the nRF51822 chip, using the the nRF SDK version 6.1, and ARM GCC.
I do not have access to Keil.
How can I achieve this?...
I'm using an old version of the nRF5 SDK (v11.0.0, SoftDevice v2) as supported by the SparkFun nRF52832 breakout board and the Arduino BLEPeripheral library.
Having set...
I am using nrf52 DK and sdk 15.0.
I want to know whether we can transfer the file over the BLE or not?
I am using ble_app_uart example,Is there any possibility to modify...
HI,the current situation is that nrf52832 can not receive the ack_payload from the nrf24le.
nrf52832 as DEVICE,using the project NRF5_SDK_13.0.0\examples\multiprotocol\experimental_ble_app_gzll...
