I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Both nrf51 & nrf52 SoftDevice specs say that this can be done:
infocenter.nordicsemi.com/index.jsp
infocenter.nordicsemi.com/index.jsp
There have been a couple of...
So, I am having a nRF51822 application that I used to upload via wired interface. Now I want my application to support so called DFU over BTLE, enabling software upload from...
Hello,
I'm trying to use nRF51 as bluetooth communication module for LPC1769 communicating over SPI, so I use connectivity firmware in nRF51 and now I'm trying to access...
Lets just stick to GPIO
I am trying to initialize multiple input buttons and multiple output LEDS.
I am trying to glow the LEDS with corresponding buttons...
Hello,
I need to know does nordic S120 stack gives the RSSI value on receiving data from peripheral? Currently I am able to get the peripheral RSSI on peripheral device...
I can not compile the example project 'ble_app_uart_s132_pca10036' ,in nRF52_SDK_0.9.2_dbc28c9\examples\ble_peripheral\ble_app_uart\pca10036\s132\arm5_no_packs.the error given...
The Nordic UART code was built for the UARTE using the following definitions:
#define UART0_CONFIG_USE_EASY_DMA true
#define UART_EASY_DMA_SUPPORT 1
#define UART_LEGACY_SUPPORT...
I add my own codes in nRF51-ble-bcast-mesh-sdk-8-support project,
then I find that if device_flash_init() is compile to this project,
the program cannot finish rbc_mesh_init...
Hi,
I have app + bootloader in one packet. On Android nRF Toolbox both can be updated in one step using Distribution Packet option. Is this possible on iOS?
I know it...
The BLE Central tutorial (S130 based) does not connect to my peripheral. My peripheral connects fine to the Android MCP and the 128-bit service UUID is what I expect.
I...
I use nrfgo studio to program the hex file. but I have only 128kb of flash and the softdevice took 88kb which left less then 50kb. I have a hex file of 70kb
my question is...
hello.
I develope the using the Nrf51822, bootloader and application not using softdevice llbrary.
the procedure is that one mcu send the mrf51822 by uart. and mrf51822...
Now I have generated bootloader.hex used by /DFU/bootloader.
After programming bootloader.hex and s110_nrf51_8.0.0.hex,the device's name changed to DfuTarg.
But when I...
Hell,
Wich BT dongle I can use to dawnload data fro board with nRF51822 chip on it?
If thear is App. to use for comunication and dawnloading data from electronic board with...
