I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi,
I searched here for a while and I couldn't find the answer. I implemented custom service by referencing nAN-36 and the github code. For some reasons, the github code...
Hi there,
I am trying to generate a pulse on a pin using RTC1 and PPI. Using a TIMER this works fine but my goal is to incur minimum current consumption by using only the...
I was trying to calculate analog voltage in nrf51822 through ADC.
I used analog 2 pin
ref voltage =1.2v
pre scaler = 1/3
so while i connected 0.9v to analog pin.
I see...
In the sensor datasheet it says one can use SPI_Mode 0 or 3 (doesn't say that there is anything to do to switch between them).
I connected MISO from the DK with SDO from...
I want my application to cooperate with DFU. I am using example DFU project from SDK (6.1) (from nrf6310 folder, i simplified it so it could work on PCA10000), but i need...
I increased my IRAM1 size as advised here , but now my program doesn't work anymore on the nRF51 DK.
I know the problem is somewhere in the memory allocation, because when...
I am working with nrf51422 chips version 2, so according to this table taken from the compatibility matrix v2.0, the last supported versions of SDK/SD/SDS I should refer to...
Also it seems not to advertise. What may cause this problem?
All I could found in the ble_gap.h is:
If both conn_sup_timeout and
max_conn_interval are specified...
Hi
I am trying to debug the "ble_app_hrs" example from SDK 6.1.0 (using keil IDE), on 51822 chip.
The IROM1 is defined to start at 0x16000 (meant to be used with softdevice...
I'm trying to minimize current consumption on my BLE peripheral and I wanted to know what advertising data is required. I have a custom service with a 128-bit UUID but do...
Hello!
I am using a keyboard (4x3) and the rows are configured as input PD and columns as output set, after a successful interrupt , the columns and the rows shift settings...
I am using nRF8001 bluetooth ble for my project. I would like to get the RSSI value as a reference value in my firmware. Is there any way that I can get the RSSI value from...
Hello,
I'm using the following (nRF51822-Beacon): www.nordicsemi.com/.../nRF51822-Bluetooth-Smart-Beacon-Kit
I would like to use the beacon for beacon-to-becaon and...
I am calling the spi_master_send_recv in a ISR from a GPIO using app_gpiote.c It causes a hardfault on APP_ERROR_CHECK(sd_nvic_DisableIRQ(p_spi_instance->irq_type)); Otherswise...
