I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
Hello, I want to make periodically wake up nRF52840, performing some work (connecting to MQTT broker, sending some data) and after that going to low power mode. Then the nRF52840...
Hello,
We want to use a nrf52840 as a logic controller which reads data from Modbus RTU Sensors (as Modbus RTU Master) and simultaneously is the Modbus RTU Server for an...
Hello Team,
We are trying to make Release and Debug mode for our software.When I compile a sample program I see lot of Debug information in the Mapfile. Will this influnce...
Hi Support team:
I'm using Zephyr cellular modem driver on the nRF5340 and set APN in prj.conf with 'CONFIG_MODEM_CELLULAR_APN="telenor.iot"' now. I need to set APN value...
Hello,
When building my project although the terminal doesn't show me using all the RAM, I get the following error message which fails the build.
I am using a...
Hello,
I was working on a ble communication using two nrf52dk boards while one of the two stop responding. The board is correctly recognised by the computer and segger asks...
When I am on to collect the accelerometer data from Thingy-53, only 3 sampling frequency options are provided which are 20 Hz, 62.5 Hz and 100 Hz as shown in figure. Please...
I am new to nRF chips and currently working with the nRF52810. I am developing with nRF Connect SDK and VSCode.
I have encountered an issue with the Blinky example (ncs...
Hello,
when creating a multi-image build is it possible to select the optimization level for each image individually?
Below is an example of the issue I am facing currently...
Running the Ciphersuites sample code on the nRF9161 I get Connection Refused on all attempted ciphersuites. Including after adding the CONFIG_EXTENDED_CIPHERSUITE_LIST=y to...
Hello,
Dev board: nRF52840 development board.
OS: Zephyr (NCS v2.6.0).
My requirement and What I am using...
- I want to perform DFU for application core & bootloader...
Hello Nordic Team, I am using nRF5340-DK and I have a PPK-2 for current measurements. My development environment is NRF Connect SDK v2.5.2. I used https://infocenter.nordicsemi...
Hello,
I am using the "direction finding connectionless beacon sample" to test various settings of the beacon. About setting parameters, I have the following two questions...
Hi. I'm working on a BLE system with Central and Peripheral with nRF5340 with 70msec of CONN_INTERVAL and about 1sec of SUP_TIMEOUT. The Central unit also has a UART that...
