I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
I'm working on a project were we require the use of a custom OOB key (not generated by the device itself) and LESC.
We have both the central and peripheral device to configure...
Hi ,
Our nRF52840 chip is drawing a high-current burst of about 1.5 seconds during the DFU upgrade. Because we have a 10 mA current limit on the battery, the system browns...
Hi
According to the errata at https://docs-be.nordicsemi.com/bundle/errata_nRF21540_Rev2/attach/nRF21540_Revision_2_Errata_v1.2.pdf?_LANG=enus, a 33k resistor is required...
Hi,
I'm using nrf52840 in revision 3, which has protection access port enabled by default.
My application is built with SDK15.0.0 / SDS S140 6.0.0
In order to get debug...
Hi,
I would like to receive notifications from iPhone to nRF54L15-DK over BLE. Anyone in the nRF community tried iOS notifications over BLE to tell me how it is done please...
Hello,
Current Situation
We are working with an nRF5340 device running nRF Connect SDK v2.7.99-cs2 . BLE security is configured for Just Works pairing (Security Mode 1...
Dear Nordic Team,
I am using NRF54L15 on NRF54 DK board and when trying to use/activate any other UART other than UART20 (e.g. UART21, UART22, UART00) on my project, every...
Hello, I've been developing an nRF52840 on a custom PCB for ~1 month now, and my environment was working previously. After updating my version of Jlink and installing other...
Hello.
I'm using nrf9151 with nRF Connect SDK v3.1.1 and Zephyr v4.1.99, modem firmware v2.0.2 I try to implement the full modem update. After downloading the "firmware...
Hello,
I can no longer use AT commands on my nRF9161 DK development board.
It used to work perfectly, but I don't know what happened.
I had previously completed the...
Hello,
I wanted to see if it is possible to move provisioned devices between team IDs in the NRF cloud. Right now I am using a nrf9151 to connect to the cloud. Once the...
Hello,
I am using Nordic nRF Connect SDK v3.1.1 and nRF5340DK board.
My project is based on the project: GitHub - nordic-auko/nRF5-ble-timesync-demo: nRF52 clock synchronization...
Hello,
I'm looking for more information on the soon to be released S145 softdevice for use with the NRF connect baremetal option for NRF54L. Will S145 support BLE PaWR and...
Hello, I'm using an nRF7002 with an nRF5340 host processor to detect and process WiFi beacon packets in monitor mode. I've encountered an issue where the nRF7002 appears to...
