I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hi,
I am discovering the nrf52 software with the Segger Embedded Studio environment. I have developed an application derived of the ble_app_uart example.
I have many events...
Hello,
I am getting the following error in Segger Embedded Studio v5.60
SEGGER Embedded Studio for ARM Release 5.60 Build 2021081102.47262 Nordic Edition Windows x64 ...
Hello,
I changed saadc.zip for my application needs
and would like to plot the incoming serial data from ADC as asked in
For time evaluation I would like to have...
Hi
We would like to test the “Carrier frequency offset” of the PCBA during production. Like the BT SIG test: RFPHY/TRM/BV-06-C [Carrier frequency offset and drift, uncoded...
nRF5 SDK, SD140 7.2.0
I am running a bluetooth application that also has OTA DFU capabililty via bluetooth. In my normal application I use a timer to advertise for exactly...
I need to set the SPI Mode NRF_DRV_SPI_MODE_0 for a 2nd chip (on the same SCK/MISO/MOSI) to NRF_DRV_SPI_MODE_1.The chipselect is handle by the application.
I can't do the...
Hello,
Is it possible to clone services of peripheral device connected with "Bluetooth Low Energy Standalone v4.0.0" PC application? I see it is possible in "nRF Connect...
nRF52840
NCS 1.9.1
I have successfully downloaded app_update.bin to flash and rebooted. MCUBOOT copies the new application correctly and it runs fine.
The boot process...
I opened an issue on GitHub, but the NRF Connect iOS repo has not been updated recently. Here is the link: https://github.com/NordicSemiconductor/IOS-nRF-Connect/issues/118...
Hi guys.
I'm using the development board NFR52840DK and I modified the sample in zephyr\samples\boards\nrf\nrfx to use twp buttons, sw0 and sw1.
The sw0 button reset a...
Hi,
I want to use my PC to send some message to dongle via USB, then the dongle send them to certain device via BLE.
If there is a sample that allows PC interacting with...
Hello,
I have tried running Blinky example with some Low Power directives in the code without success. I came here for help then.
The current consumption used by the example...
Hi All,
I am trying to port my current SES project (s140) from nrf52833 to nrf52832. My nrf52832 is spec'd at 512kb flash and 64kb RAM. Any help would be much appreciated...
Hi,
Trying to evaluate the nRF52840DK with Matter examples but none of them seem to compile.
Following error is the result
Building light_switch west build --build-dir...
Hi,
We are using nrf5340 nrf connect SDK V2.0.0 and we are unable to find the brownout detector configuration. For our use-case we want to trigger system reset if supply...
